What specialist testing can show
TI-5000JX bench. Check incremental and commutation paths independently with the matched 28-contact connection.
TI-3000JX motor run. Confirm the motor-specific run profile, pole count and alignment before use.
Starting lead. TI-5714 for the 28-contact Tyco CPC incremental branch.
Allen-Bradley Kinetix TLY H Incremental ABZ/UVW Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| TLY-A130T-HK62AN | Exact Rockwell example, 46 mm frame, H incremental, no holding brake. |
| Kinetix TLY H | Incremental branch. Mitchell lists TI-5714 for the 28-contact Tyco CPC ABZ/UVW connection. |
| Kinetix TLY B | Battery-backed serial branch. Mitchell lists TI-5715 for the same connector family with different wiring. |
Production and end-of-life status
Rockwell lists TLY-A130T-HK62AN as Active Mature. Verify exact supply and configuration before replacing the motor or encoder.
Specifications
| Parameter | Verified scope |
|---|---|
| Resolution | 2,000 encoder lines per revolution for the stated H motor. Controller count scaling depends on edge decoding. |
| Example motor mounting | 46 mm frame, 43.8 mm flange bolt circle and unkeyed shaft per Rockwell. These are external motor dimensions. |
| Feedback circuits | Incremental A/B/Z and U/V/W commutation on the Mitchell TLY H test connection. |
Interface and measuring method
A and B give direction and incremental travel. Z is the index. The commutation channels identify rotor sectors for the motor. A drive can receive A/B counts and still trip when a commutation channel is missing or out of phase.
Mounting and fit
The Rockwell dimensioned sheet identifies the motor and cable exit. Establish the complete encoder mounting from the motor service drawing. Record shaft reference, housing position and rear cover cable routing before removing a fitted unit.
Wiring and connector scope
Use the Rockwell drive and feedback cable documentation for the actual connector option. Keep motor U/V/W phase leads separate from the encoder U/V/W commutation circuits. Match the shell, mating face and feedback supply using the drawing before measuring.
Internal motor and machine cables
Identify the motor pigtail and the drive extension by their own part numbers. TI-5714 is the shop test lead. Record the OEM internal harness and plug if the fault follows strain at the motor end.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Counts change but enable trips | Check the commutation circuit, motor phases and fitted H configuration separately. |
| Loss of feedback while the cable flexes | Inspect and isolate-test the CPC harness and contact retention. |
| Wrong motion scale | Compare controller quadrature count settings with the 2,000-line nameplate specification. |
Angle of alignment and commissioning
Record the index and U/V/W sequence relative to the motor phases where the OEM procedure supports it. Confirm the original motor reference before changing a rear encoder or attempting a powered run.
Motor and drive applications
Kinetix TLY H, exact A130T OEM example
Separate H incremental from B battery-backed serial and select the correct drive cable and receiver.
Drawings, pin maps and manuals
- Mitchell Test Cable Index by Manufacturer. Allen-Bradley section, TI-5714 TLY Series ABZ/UVW
- Rockwell TLY-A130T-HK62AN exact cut sheet. Supplementary reference for the stated model or setup.
- Rockwell Kinetix 2000 system design, TLY H cable note. Reference for the fitted feedback or motor option.
- Rockwell TLY-A130T-HK62AN motor dimensions. Exact order mechanical drawing. Use the Kinetix design manual for the drive-side cable map.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.