Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
A manufacturer evaluation setup or documented PCB breakout can check SPI angle, error flags and magnet diagnostics. A logic analyzer can compare frame timing and output transitions. Confirm the equipment maker's circuit and procedure before interpreting powered measurements or selecting a Mitchell profile.
ams OSRAM AS5047P-ATSM Magnetic Angle Sensor IC technical reference
Find your part number
Use the full label and suffix. The main reference is AS5047P-ATSM. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| AS5047P-ATSM | TSSOP-14 magnetic sensor IC. 500 pieces per reel in the ordering table. | AS5047P silicon with 14-bit SPI angle and configured output modes. |
| AS5047P-ATST | Same TSSOP-14 part marking. 4,500 pieces per reel. | Same model in a different delivery quantity. Verify purchasing suffix. |
| AS5047D-ATSM | Related TSSOP-14 IC. Compare the exact design and magnet drawing. | Separate sensor model. Verify ABI configuration, registers and output behavior before substitution. |
Production and end-of-life status
ams OSRAM documents both AS5047P reel codes in the ordering table. Confirm lifecycle and procurement status for ATSM with the manufacturer.
Specifications
| Parameter | Value and scope |
|---|---|
| Measurement | On-axis Hall-based magnetic angle sensor. 14-bit absolute SPI reading within one turn. |
| Interfaces | SPI and configurable ABI, UVW and PWM outputs. Read the programmed settings for the board. |
| Power | The datasheet gives distinct 3.3 V and 5 V application circuits. Determine the PCB implementation from its schematic before applying power. |
| Package | TSSOP-14. Locate pin 1 and confirm the part marking before probing or replacing. |
| Mechanical reference | Use the documented diametrically magnetized target and specified field at the die. Magnet spacing depends on the assembly and magnet. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
The IC is soldered to a PCB and senses a separate rotating magnet. Check PCB location, magnet centering, retention and axial position against the device manufacturer's design. Check for nearby steel, debris and evidence that the magnet shifted. A replacement IC needs the proper package, ESD process, pin orientation and PCB assembly procedure.
Interface and measuring method
Hall elements sense the direction of the magnetic field and the IC calculates an angle. SPI gives the controller an absolute reading and diagnostic registers. The board can also use the configured incremental, commutation or PWM outputs. A valid SPI response with weak-field diagnostics points toward the magnet geometry or environment. A valid angle with incorrect ABI or UVW output can point toward configuration.
Verified wiring
Use the top-view TSSOP-14 drawing and the chosen power-management circuit in DS000324. These are IC pins. The machine connector has the equipment maker's mapping.
| Pins | Functions in pin order |
|---|---|
| 1 / 2 / 3 / 4 | CSn / CLK / MISO / MOSI |
| 5 | TEST, connect as shown in the datasheet |
| 6 / 7 | B / A |
| 8 / 9 / 10 | W or PWM / V / U |
| 11 / 12 / 13 | VDD / VDD3V3 / GND |
| 14 | I or PWM |
Verify that you are following the board's documented supply circuit. Observe the input and output limits at the IC and use approved probes or test pads.
Cables inside the motor and at the machine
AS5047P-ATSM is a PCB component. Order or build any external harness from the assembled equipment drawing. Match the board header and logic domain, shield and strain relief at the receiver. Treat a breakout module as its own part with its own map.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| SPI response absent or parity errors | Check the board supply, chip-select, clock, logic levels and frame timing at approved test points. |
| Angle drifts or jumps while communication holds | Read the field diagnostics and check magnet movement, centering and air gap per the assembly drawing. |
| SPI angle valid, incremental or commutation output wrong | Compare live configuration and direction against the documented design before programming. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
This guide applies to the AS5047P-ATSM component inside an equipment design. A motor or robot using it may combine magnetic feedback with separate power stages, speed limits and commissioning software. Identify the PCB assembly and magnet part alongside the IC.
Angle of alignment and commissioning
Record the magnet position, board orientation and current settings before replacing the board or IC. Verify zero, direction and output behavior against a known datum. Use the approved OEM process for configuration or OTP programming. Readback and functional checks matter before any irreversible programming.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- DS000324 pin and timing diagrams. Distributor mirror of the ams datasheet.
- ams OSRAM order code notice PN000157. Use the exact ATSM entry. Review the notice's scope and date when sourcing.