Site visit or send-in evaluation
Provide the sensor code, cylinder or machine drawing, magnet type, PLC channel configuration, current and indicated position at known points. Include symptoms and mounting photos. Use the enquiry form to share the details.
What specialist testing can show
Use a compatible magnet, regulated supply and appropriate analog input or test load to compare measured current with known position. Check the LED status and approved teach settings. A loop calibrator used on the isolated PLC input can separately check the PLC scaling. Exact Mitchell TI-5000JX or TI-3000JX use with this analog linear sensor was not verified. Balluff setup and analog output diagnostics (PDF)
Balluff BTL070F 4–20 mA Linear Position Sensor technical reference
Find your part number
Find BTL070F and BTL7-E501-M0200-B-S32. E501 identifies the analog current build, M0200 the 200 mm measuring length, B the rod mounting configuration, and S32 the 8-contact M16 connection. A 200 mm measuring length is distinct from the rod's installation length.
| Balluff ID / model | Stroke and output | Mount or connector difference |
|---|---|---|
| BTL070F · BTL7-E501-M0200-B-S32 | 200 mm, 4–20 and 20–4 mA factory output directions | Rod with M18 × 1.5 flange. 8-contact M16 S32. |
| BTL070E · BTL7-E501-M0150-B-S32 | 150 mm, E501 analog current | Similar rod and S32 connector. Different measuring length. |
| BTL1E22 · BTL7-E501-M0200-P-S32 | 200 mm, E501 analog current | Profile design. Use its own mounting and magnet documentation. |
BTL070F exact datasheet (PDF) · BTL070E exact comparison · BTL1E22 profile comparison
Production and end-of-life status
Balluff publishes the exact BTL070F record and product drawing. Confirm current supply, repair or substitute using the Balluff order code and the complete type. Balluff exact BTL070F product record
Specifications
| Parameter | Value |
|---|---|
| Measurement | 200 mm magnetostrictive linear travel. Maximum sampling frequency 4000 Hz per exact sheet. Check settings and magnet arrangement. |
| Installation | M18 × 1.5 threaded flange, Ø10.2 mm protection tube, 290 mm installation length from contact surface. The drawing shows a 30 mm null distance. |
| Outputs and supply | Factory analog output 1 at 4–20 mA, output 2 at 20–4 mA for the documented S32 E501. Supply 10–30 V DC. |
| Electrical connection | S32 8-contact M16 × 0.75 connector. Use exact E501 S32 column. |
| Performance and environment | ±50 µm maximum nonlinearity, ±5 µm repeatability, −40 to +85 °C ambient and IP67 with the connector fitted. |
Exact Balluff dimensions, values and performance (PDF) · Balluff E501 settings and pinout (PDF)
Mounting and fit
A position magnet moves along the fixed sensing rod. Use the cylinder and Balluff drawings to match the threaded seat, seal, magnet, material and rod support. Check actual insertion and end clearance through the full permitted travel. Measure from the mounting contact surface as specified. A replacement with the same nominal measuring range can still differ in installation length or magnet arrangement. Follow the cylinder OEM procedure for a pressure-boundary installation. BTL070F exact installation dimensions (PDF) · Balluff rod, magnet and cylinder installation (PDF)
Interface and measuring method
The sensor measures the travel time of a pulse associated with the position magnet and converts position to analog current. The PLC converts that current to machine units. With the default increasing output scaled over an unmodified 200 mm span, 4 mA is one endpoint, 12 mA the midpoint and 20 mA the other endpoint. Actual zero/endpoints, rising or falling output and invalid-position behavior depend on configuration. Compare current and independent travel before changing a teach setting. Balluff principle, analog behavior and adjustment (PDF)
Verified wiring
Use the S32 E501 assignment in Balluff table 4-2. Read the connector-pin view from the sensor side. The factory KA lead colours in the manual are separate reference information. Check the actual mating cordset.
| Pin | Function |
|---|---|
| 1 | Output 1, 4–20 mA factory setting |
| 2 | 0 V supply return |
| 3 | Output 2, 20–4 mA factory setting |
| 4 | La communication / programming |
| 5 | Unused for E501 |
| 6 | GND per Balluff wiring notes |
| 7 | 10–30 V DC supply |
| 8 | Lb communication / programming |
Keep the output references, programming lines and shield arrangement as the Balluff and PLC diagrams specify. The A501 voltage-output model and the S115 M12 variant have different assignments. Balluff S32 drawing, table 4-2 and wiring notes (PDF)
Cables inside the motor and at the machine
The S32 rod sensor is external to a servo feedback loom. Balluff lists BCC00TT straight and BCC00UP angled 8-contact M16 mating connectors. The earlier manual lists 5 m molded BCC0L21. Confirm exact cordset termination, pressure-system routing and shielding for the installation. Choose the magnet from the approved Balluff and cylinder drawings. Balluff S32 accessories and magnet drawings (PDF) · BCC0L21 5 m cable example (PDF)
Fault checks
Isolate hydraulic or pneumatic pressure, secure the load, and verify residual energy before disturbing the rod or magnet. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
- Record. Read raw PLC input and machine position at known points under the approved procedure. Capture output choice, teach settings, LED status and what changed.
- Inspect under isolation. Check connector key and seating, water or oil ingress, rod straightness and magnet retention or travel against the drawing. Verify that the input channel is configured for current.
- Check the detached harness. With the harness isolated from the encoder and receiver at both ends, use resistance mode. First short the meter probes to establish lead resistance. Check each conductor end to end and flex the cable gently at the strain relief. Check between unrelated wires and from signal wires to shield or shell. Expect open only where the drawing calls for isolation. Compare any intentional sense links or shield bonds with the equipment drawing. Keep insulation testers away from connected electronics. Use Balluff's pinout and intentional bonds for the reference.
- Check voltage and current separately. A qualified technician can use an approved breakout fitted while off, then measure pin 7 to 2 under load in the approved test state. Read current using the verified input or an approved series test connection. Keep the meter's current input out of a supply voltage measurement. Compare current against known movement.
- Separate faults. If current changes correctly but engineering units are wrong, check input mapping and scaling. If output remains unchanged, check the magnet and teach limits before diagnosing the head. A sensor-side signal that disappears at the PLC points toward the cable or input circuit.
Motor and drive applications
This rod-style magnetostrictive feedback is used for compatible machine-axis or cylinder position measurement. Match range, rod geometry, connection, magnet and output configuration to the machine. The similar profile form has a different mounting arrangement. BTL070F exact rod data (PDF) · BTL1E22 profile form
Angle of alignment and commissioning
Confirm the mechanical magnet path and authorized cylinder end limits. Record the original output selection, teach points and PLC scale. Set approved endpoints only at known secured positions using the Balluff procedure. Verify both directions and a midpoint before releasing the machine. This measurement uses a linear datum rather than a motor commutation angle. Balluff analog calibration and teach procedure (PDF)
Drawings, pin maps and manuals
- Balluff BTL070F exact datasheet (PDF). Installation dimensions, nominal length and operating data.
- Balluff BTL7 A/E501 rod user guide (PDF). S32 E501 wiring, mounting, outputs and diagnostics.
- Balluff BTL7 accessory reference (PDF). Includes the BCC0L21 S32 cable example.
- Balluff exact product and downloads. Check the full material code and current support.