What specialist testing can show
TI-5000JX bench. Use the stated Hall-state and tach test paths. Compare the AC tach response separately.
TI-3000JX motor run. Mitchell describes Generic Pulse 120° for the correctly matched and aligned assembly.
Starting lead. TI-5071 on the documented plug. Verify connector revision before matching the fixture.
Baumüller DS Hall / AC Tach Commutation and Speed Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| DS Hall / AC tach with 17-contact M23 | Mitchell lists TI-5071 and the TI-5105 module for the documented test. |
| DS Hall / tach with 15-contact Heavymate D | Separate TI-5729 connector branch with TI-5105 in the index. |
| DS resolver | The Mitchell index lists a separate 12-contact resolver branch. Check the full order before selecting the fixture. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Commutation | Three Hall state channels, H1 to H3 in the Mitchell article. |
| Speed feedback | Three-phase AC tachometer on the scoped DS build. |
| Test display | Mitchell uses Generic Incremental to display Hall states. |
Interface and measuring method
Hall states identify rotor sectors. The AC tachometer provides a speed-related signal. Compare the Hall sequence and the tachometer response independently and record the test direction and motor order.
Mounting and fit
Record the housing and tachometer reference before dismantling. Mitchell discusses a possible keyed relationship for the illustrated assembly. Verify the actual fit from the matched drawing before assuming the key sets its reference.
Wiring and connector scope
Use the exact TI-5071 or TI-5729 wiring reference as applicable, with the matching motor schematic. Identify the Hall circuits, their supply, the three tach conductors and the separate motor power connection.
Internal motor and machine cables
Check the motor connector and cable retention before removing the feedback assembly. An original DS internal harness and the shop test adapter have different functions. Record the actual plug and full motor type for a spare.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Motor commutation fault with tach output | Check Hall states and phase reference on the correct fixture. |
| Hall transitions present with speed error | Check tach winding continuity under isolation and the expected tach waveform on an approved setup. |
| Signal drops when the plug is moved | Inspect and isolate-test the correct M23 or Heavymate harness. |
Angle of alignment and commissioning
Mitchell provides a scope relationship for the documented Hall/tach assembly. Confirm phase, direction and tachometer reference with that drawing and the actual motor. Back-driving a motor for waveform checks requires the approved guarded specialist setup.
Motor and drive applications
Baumüller DS with documented Hall/tach option
Trace a commutation fault separately from missing speed feedback and choose the actual DS plug.
Related SpareFaber guides
Drawings, pin maps and manuals
- Baumüller motors with Hall commutation and three-phase AC tach feedback. Hall and AC tach feedback, TI-5071 / TI-5105 and test/run section
- Mitchell Test Cable Index by Manufacturer. Supplementary reference for the stated model or setup.
- Mitchell TI-5071 test lead drawing. 17-contact M23 lead for the documented DS configuration.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.