Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Use the FANUC line-tracking diagnostics or a qualified differential incremental signal test to compare direction, index and counts with measured movement. Confirm any Mitchell fixture for the exact connector before connecting. TI-3000JX motor-run support is outside this external Pulsecoder application.
FANUC A860-0301-T001 Line Tracking Pulsecoder technical reference
Find your part number
Use the full label and suffix. The main reference is A860-0301-T001. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| A860-0301-T001 | External conveyor tracking Pulsecoder. See FANUC Figure C.2(c) for shaft and mounting dimensions. | Incremental A/B/Z. Match the exact R-30iB or R-30iB Mate option. |
| A860-0301-T002 / T003 / T004 | Related variants in FANUC Appendix C. Use their appropriate drawings. | Check exact suffix and signal requirements before comparing. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Feedback role | Incremental external Pulsecoder for line tracking in FANUC B-83474EN/02, Appendix C. |
| Connection | FANUC figure C.2(a) identifies 310A20-29P and the A/B/Z signal and power contacts. |
| Signal reference | +5 V supply contacts per figure C.2(a). Use figure C.2(b) for electrical limits and resolution. |
| Host | R-30iB or R-30iB Mate with the applicable line-tracking interface configuration. |
The table identifies the assembly each value applies to.
Mounting and fit
Identify where the encoder measures conveyor movement. Check the coupling or drive wheel for slip, backlash and repeatable engagement over the measured travel. With the conveyor locked out and restrained, inspect the shaft retention, bracket and cable strain. Use Appendix C.2(c) to compare dimensions.
Interface and measuring method
A and B indicate direction and movement. Z is the reference pulse. The controller converts counts to conveyor distance using the configured tracking scale. A good pulse train with the wrong tracking direction or scale usually points to coupling geometry or configuration, so compare counts against measured travel.
Verified wiring
Use this only for A860-0301-T001 and follow the FANUC contact drawing. Controller-side connectors differ by board option.
| Contact or group | Function |
|---|---|
| A / D | A / complement of A |
| B / E | B / complement of B |
| F / G | Z / complement of Z |
| C, J, K | +5 V group |
| N, P, T | 0 V group |
| H | Shield per FANUC drawing |
Cables inside the motor and at the machine
Use the exact installed controller and line-tracking board number to choose the cable. Appendix C.3 maps cable paths for boards such as A05B-2600-J035 and A05B-2660-J035. The Pulsecoder cable and machine interface lead are separate drawings. Confirm JF21/JF22 assignment from the fitted board before ordering or testing.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Line count stays fixed while the conveyor moves | Inspect shaft/wheel engagement, then verify the correct board input, power and A/B path. |
| Tracking error increases with distance | Compare counts with actual travel and check wheel diameter, gearing or configured scale. |
| Count direction reverses unexpectedly | Check the A/B assignment and tracking direction under the documented FANUC procedure. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare the documented supply or excitation under the specified load. Use the approved receiver or instrument to observe the appropriate data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
FANUC specifies this Pulsecoder in the R-30iB and R-30iB Mate line-tracking documentation. Check Appendix C for the installed board and whether the application has one or two Pulsecoders.
For serial servo-axis feedback, use the separate fitted Pulsecoder guide. FANUC αiI1000 guide.
Angle of alignment and commissioning
This task is conveyor measurement and calibration. Use the FANUC line-tracking procedure for sign, measured counts per distance and tracking datum. Verify measured motion at safe test conditions before returning the conveyor and robot to coordinated operation.
Drawings, pin maps and manuals
- FANUC B-83474EN/02 Line Tracking operator manual. Manufacturer-authored mirror. Appendix C.2(a)–(c) gives connection, specifications and dimensions. Appendix C.3 gives board-specific cables.
The references above describe the verified scope. A direct technical PDF for the exact encoder remains to be confirmed.