What specialist testing can show
TI-5000JX bench. Mitchell lists the high-speed Alpha A32000i profile for TI-5000JX. Use the appropriate firmware and verified serial path.
TI-3000JX motor run. Verify the A06B motor order, drive and specific supported run profile before a motor run.
Starting lead. TI-5750 on the verified two-wire high-speed branch.
FANUC αA32000i High-Speed Serial Pulsecoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| αA32000i | FANUC Alpha A32000i is a named high-speed TI-5000JX selection in the Mitchell release notes. |
| A860 order and A06B motor order | Record the fitted encoder and motor labels. The A860 suffix is required to establish exact mounting and connector fit. |
| Earlier FANUC serial branch | Mitchell distinguishes high-speed two-wire data from the earlier four-wire SD/REQ connection. Choose by actual wiring. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Supported diagnostic selection | Alpha A32000i in the high-speed TI-5000JX list. |
| High-speed branch | Differential RD data pair in Mitchell’s two-wire arrangement. The supply and return are separate. |
| Exact assembly | Use the original motor, Pulsecoder and amplifier documentation for count scale, retention, connector and supply details. |
Interface and measuring method
The amplifier receives serial position and status from the Pulsecoder. A supply measurement checks power only. A valid response on the matched serial tester provides separate evidence about the communications path.
Mounting and fit
Use the A860 and A06B labels to obtain the fitted rear assembly drawing. Record cover, shaft attachment, locating features and cable exit before changing mechanical position.
Wiring and connector scope
Compare the actual motor plug with the FANUC high-speed reference. Mitchell names TI-5750 for two-wire RD data and TI-5047 for the earlier four-wire branch. Confirm the plug and supply independently before connecting.
Internal motor and machine cables
Find the original FANUC cable assembly from the motor and amplifier orders. Preserve the fitted shield termination and cable routing. Keep the test fixture separate from the machine harness.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Tester shows no data | Check the high-speed selection and compare the fitted serial pairs to the correct cable sheet. |
| Bench reply is stable but the machine faults | Compare the complete machine harness and drive receiver with the short test path. |
| Reference alarm follows service | Review the OEM reference and retention procedure before changing any stored position. |
Angle of alignment and commissioning
Save drive parameters, the existing machine reference and the incoming feedback record. Verify reference recovery and motor compatibility under the FANUC commissioning instructions after fitting.
Motor and drive applications
FANUC Alpha i with verified A860 order
Confirm the fitted A860 suffix, connector generation, compatible lead and mechanical drawing.
Related SpareFaber guides
Drawings, pin maps and manuals
- Athena 5.1.0.2262 and TI-5000JX 5.1.0.13 release notes. New Encoders, Alpha A32000i
- Mitchell FANUC High Speed Serial Encoders. Two-wire and four-wire data connections and matching test leads.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.