Identify the fitted part
| Guide scope | Hengstler AC59 / AC61 parallel — Standalone device |
|---|---|
| Feedback identity | AC59 / AC61 parallel |
| Manufacturer MPN / full suffix | AC59 / AC61 parallel is the scoped family/designation. Match every additional character on the fitted label before ordering. |
| OEM service ID / motor order | Not established for a specific fitted unit. Record the full motor label, feedback option and any OEM service ID separately. |
| Interface | Parallel absolute, exact code/width by order |
| Documented starting connection | Exact-order parallel fixture and bit-width check required |
| Material distinction | TCG419 is AC59/AC61 SSI/BiSS. Parallel output requires a different fixture and acquisition method. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional parallel position check only after exact bit count, code, supply and fixture are verified. No SSI/BiSS or fieldbus support inferred. |
|---|---|
| Starting lead / fixture | Exact-order parallel fixture and bit-width check required |
| Profile / module | Parallel input capacity, bit width, code format and signal level to match exact order. |
| TI-3000JX motor-run scope | No complete motor-run approval established by this proposal. Verify motor poles, power/brake wiring, alignment, fixture and the installed TI-3000JX profile. |
The admission evidence is Hengstler Encoders — Absolute Encoders, AC59/61 Stainless Absolute Encoder with Parallel Wiring. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
A manufacturer family or item record is linked below. Its presence is not confirmation that every historical suffix is available. Obtain current status and any proposed successor against the full label; fit, output, connector and motor data must all be checked.
Specifications and interface
| Parallel code | PB = binary; PG = Gray. A = 5 V and E = 10–30 V in the historical order table; verify the fitted order before applying either. |
|---|---|
| Singleturn choices | 10/12/13/14/17 bits, or special 360/720-step orders. The special orders have offsets of 76/152 respectively; code value is not necessarily zero at the mechanical datum. |
| Multiturn choices | AC61: 4/8/12 multiturn bits plus 12 singleturn bits. AC59 is marked singleturn only in this parallel order table. |
| Mechanical options | Q.76 square flange with 9.52 mm shaft or Q.72 with 10 mm shaft; axial A or radial B cable. Use the corresponding dimensioned drawing. |
| Supply / output compatibility | Use the complete fitted label and its wiring drawing. No universal supply, receiver level or excitation is assigned to this family guide. |
| Exact dimensions, torque and pins | Use the scoped drawing or request it through the enquiry. Values from another suffix, connector view or motor revision are not substituted. |
A parallel encoder presents position bits on separate conductors. Match binary versus Gray code, singleturn and multiturn bit allocation, supply and receiver thresholds. Latch, direction, tristate and alarm functions belong to the exact connection diagram; a serial SSI/BiSS tester lead is not a parallel fixture.
Mechanical fit and retention
Photograph the incoming shaft/coupling position, locating seat, restraint, fasteners and cable exit before removal. Check accessible looseness, contamination, bearing roughness and signs of rubbing after isolation. Identify whether the assembly has its own bearings, a hollow-shaft clamp or a motor-retained sensor; the exact drawing controls that decision. Do not lever against a sensing disc or apply a torque from a similar-looking model.
The parallel AC59/AC61 datasheet distinguishes PB binary from PG Gray. AC59 is singleturn in its order table; AC61 also offers 4/8/12 multiturn bits plus 12 singleturn bits. Cable diagrams differ for 10–14-bit ST, 17-bit ST and MT; do not use an SSI/BiSS connection sheet.
Wiring and connector boundaries
Map five boundaries separately: the sensor plug or PCB, internal motor loom, motor bulkhead, external machine cable and drive/tester end. Record connector gender, keying, contact numbering and whether the drawing shows mating or termination side. The documented Mitchell lead is a starting fixture, not a pin map for a handmade adapter. Keep power, temperature, brake, shield and feedback contacts identified individually.
Starting connection for this guide: Exact-order parallel fixture and bit-width check required. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
No internal OEM harness number or universal extension has been verified for this exact fitted order. Obtain the motor assembly drawing and photograph both loom ends before sourcing it. A fixed installation cable and a cable-carrier extension may have different flex and shielding requirements. Do not convert the Mitchell test-lead number into an OEM replacement part number.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Configuration-specific check | The parallel AC59/AC61 datasheet distinguishes PB binary from PG Gray. AC59 is singleturn in its order table; AC61 also offers 4/8/12 multiturn bits plus 12 singleturn bits. Cable diagrams differ for 10–14-bit ST, 17-bit ST and MT; do not use an SSI/BiSS connection sheet. |
|---|---|
| Fault appears when the machine cable moves | With the system isolated and both ends disconnected, inspect flex points, connector engagement and repaired sections. Check end-to-end continuity and unintended shorts against the actual pin map, accounting for intentional shield bonds. |
| No feedback or intermittent loss at the drive | After label and fixture verification, have a qualified technician check the specified supply or excitation through an approved breakout. Compare at the source and load under the OEM procedure; never assume a voltage from the connector shell. |
| Position reads but status or retained reference is wrong | Save detected identity, status and incoming position. Check the documented profile and retention arrangement before a reset, battery intervention or data transfer. |
Alignment, reference and memory
Record mechanical zero, direction and the receiver code/bit settings before removal. Special 360/720-step orders have nonzero code offsets in the table. Establish any latch, direction or preset function from the exact order rather than applying an SSI or HIPERFACE memory procedure.
Motor and drive applications
Standalone feedback family; exact complete device order to verify. TCG419 is AC59/AC61 SSI/BiSS. Parallel output requires a different fixture and acquisition method.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Hengstler Encoders — Absolute Encoders, AC59/61 Stainless Absolute Encoder with Parallel Wiring
- Generic Parallel Absolute Encoders — Named article section, model or attached table. See each proposal row for the exact scope and locator.
- AC59_61-Parallel_Datasheet_EN.pdf — Manufacturer datasheet: ordering codes, electrical connections and mechanical drawings for the exact interface and fitted suffix.
- Manufacturer record / drawing directory — Select the complete fitted order; family identification is not a fit or stock guarantee.
Primary family/application PDF linked; exact fitted order, fixture, internal loom and alignment evidence remain to confirm.
Common questions
What should accompany a AC59 / AC61 parallel enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
No complete motor-run approval established by this proposal. Verify motor poles, power/brake wiring, alignment, fixture and the installed TI-3000JX profile. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.