Site visit or send-in evaluation
We compare the exact AD58 order code to the drive profile, then diagnose the supply, serial link or mechanical fit. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Mitchell lists AD58-0022 under Generic BiSS. Obtain confirmation for the BI Mode B suffix, the correct fixture and firmware before using TI-5000JX. A Mode B capable bench receiver can compare supply, valid frames and repeatability. Confirm complete-motor TI-3000JX compatibility separately.
Hengstler AD58/0022E1.0KBI0 0547029 BiSS-B Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is AD58/0022E1.0KBI0. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| AD58/0022E1.0KBI0 / 0547029 | 1.0K spring tether and 1:10 tapered solid shaft. 0 denotes the axial 12-pin PCB connection. | 0022 = 22-bit single-turn. E = 10–30 V DC. BI = BiSS-B without the optional sin/cos output. |
| AD58 with BC | Check the complete code for tether and shaft. | BiSS-B with optional 1 Vpp sin/cos track in the ordering table. |
| AD58 with BE or BV | Compare shaft, connector and tether code. | BiSS-C variants. BV includes a sin/cos track. |
Production and end-of-life status
Hengstler's exact product page offers item 0547029. Confirm orderability and production status for the complete BI0 code when sourcing.
Specifications
| Parameter | Value and scope |
|---|---|
| Position | 22-bit single-turn, 4,194,304 positions per turn |
| Link | BiSS Mode B, BI code |
| Power at the encoder | 10–30 V DC on the E variant |
| Connection | Axial 12-pin PCB connector, code 0 |
| Mount | 1:10 tapered solid shaft, K code, with spring tether. 58 mm housing family. |
| Enclosure | IP40 for the 1.0K order-code combination. |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
Use the K-shaft mating dimensions to verify the taper and central retention. The spring tether restrains the housing and allows the specified movement. With the motor isolated, inspect the tether for distortion, the taper for seating marks, and the lead for pinching. Confirm which fastener and setting the motor maker uses on this build.
Interface and measuring method
The downstream receiver clocks a BiSS response from the encoder. The BI suffix selects the Mode B interface. Match the receiver's frame handling and device selection to that mode before interpreting an idle line or invalid position. The AD58 family also includes Mode C and SSI configurations.
Verified wiring
These are the supply and digital signals in Hengstler's 12-position PCB diagram, identified by row a and row b. Use the matching PCB drawing and connector orientation. The optional analog and sense positions are described separately in the datasheet and need the exact drive and harness drawing.
| Function | Cavities |
|---|---|
| Supply / return | 1b / 4b |
| Clock / inverse clock | 2b / 5a |
| Data / inverse data | 6b / 1a |
Use the E-code range, 10–30 V at the encoder, for supply checks. The pin drawing includes multiple family supply options.
Cables inside the motor and at the machine
The code 0 connector is axial at the PCB. Match the key, row numbering and motor harness before ordering. The AD58 ordering table also lists other connector packages. Confirm the full motor part number for the cable from the encoder PCB to the drive or motor outlet.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Receiver reports invalid frames or cannot find the encoder | Confirm the BI Mode B profile and the exact clock/data pair mapping. Check loaded power. |
| Reads at rest but drops out during travel | Inspect strain relief, cable shield and supply drop. Test the disconnected harness with gentle flex at the failure point. |
| Position count is stable but drive enable faults after service | Verify taper seating, tether and original motor configuration. Check the OEM reference and direction. |
| A candidate replacement has a different letter pair | Read the manufacturer's order decoder and confirm both protocol and mechanical codes before fitting. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Hengstler identifies 0547029 as the exact encoder. The complete fitted motor is still open. Kollmorgen’s AKD BiSS-C example uses the AD58-0022 family shorthand and explicitly applies to Mode C. Check the drive model for a documented Mode B input before applying it to 0547029.
Angle of alignment and commissioning
Record the installed taper and tether orientation and preserve the motor's reference or offset by the applicable OEM method. The 22-bit count describes resolution. The required direction, datum and commutation offset come from the motor and drive assembly.
Drawings, pin maps and manuals
- Main technical PDF. Hengstler AD58 datasheet v3 260423 HF, manufacturer-authored copy. Page 2 shows the PCB assignments, page 3 the K-shaft drawing and page 5 the ordering key.
- Manufacturer reference. Match the exact order code or the identified motor option.
- Mitchell Athena feedback support note. AD58 family shorthand. Confirm the exact BiSS mode with Mitchell.
- Kollmorgen AKD BiSS-C compatibility note. Scope of the separate Mode C guide.