Site visit or send-in evaluation
Share the entire motor code including the connector and feedback characters, AKD2G model and firmware, fault text and the cable marking. Include whether the fault began after a motor, drive or cable change. Use the enquiry form to share the details.
What specialist testing can show
Use a supported Kollmorgen drive and matching cable to read motor identity, feedback type, position and diagnostics. Compare the fault with a verified cable or approved service fixture. Mitchell states that its JX equipment does not directly decode proprietary SFD or SFD3 serial. A published resolver-side bypass applies only where the matching internal assembly and procedure are verified, and it cannot validate the SFD3 serial path. AKD2G supported feedback types · Mitchell scope for SFD/SFD3 bench work
Kollmorgen AKM2G SFD3 CA Motor Feedback technical reference
Find your part number
Read the full AKM2G motor type, the CA feedback code and the separate connector code. This guide focuses on CA with the D hybrid connector, with other codes as comparisons. The servo name, SFD family and external connector are each needed to identify a replacement.
| Nameplate combination | Feedback | Connector distinction |
|---|---|---|
| CA · D | SFD3, two-wire absolute singleturn | D hybrid under 20 A continuous in the cited pinout. SFD pair H/L. |
| CA · A | Same SFD3 feedback protocol | Legacy AKM cable pinning on applicable AKM2G. SFD pair C/D. |
| CA · J | Same SFD3 feedback protocol | Separate J hybrid for AKM2G7 >20 A in the cited pinout. SFD pair 6/7. |
| CB · SFD-M | Two-wire absolute multiturn | Use the specific CB motor and connector documentation. |
| GU · HIPERFACE DSL | Different two-wire feedback system | Confirm its dedicated connector, drive setup and cable. |
AKM2G feedback options (PDF) · Kollmorgen connector drawings (PDF) · AKD2G feedback types
Production and end-of-life status
Kollmorgen's AKM2G installation and feedback documentation list SFD3 code CA. Confirm current manufacture, repair and replacement for the complete motor and connector code. Kollmorgen AKM2G options (PDF)
Specifications
| Parameter | Documented scope |
|---|---|
| Measurement | Singleturn absolute feedback. Kollmorgen describes a resolver sensing element with digital electronics in SFD3. |
| Drive link | Two wires carrying DC power and AC-coupled proprietary serial communication on an RS-485 physical link. |
| Data | Shaft position, motor temperature and motor catalog parameters stored in the feedback device as documented by Kollmorgen. |
| AKD2G feedback type | SFD3 is type 45 in the cited AKD2G manual. SFD-M is a separate type. |
| Mechanical and supply details | Built into the AKM2G motor. Use the specific motor drawings and Kollmorgen drive/cable for interface electrical limits. |
Kollmorgen SFD3 architecture · AKD2G type descriptions · AKM2G temperature and option notes (PDF)
Mounting and fit
SFD3 is internal to the motor. First confirm whether the fault follows the external cable or drive input before opening the motor. Check the hybrid connector key, lock, shell and strain relief under isolation. Preserve the original feedback position and connector arrangement. Request motor-specific internal mechanical and service drawings before moving the resolver, board or motor end cover. Kollmorgen motor installation and handling (PDF) · External connector and configuration (PDF)
Interface and measuring method
SFD3 and the drive share the feedback pair for power and communications. At startup the drive can read the motor's identity and stored parameters. A connector can look similar to a DSL or another SFD version while using a different protocol or contact assignment. A normal shaft angle at one position does not establish communication or motor identity across the service range. Kollmorgen two-wire interface and data · Drive feedback compatibility
Verified wiring
These are the motor-end feedback contacts only in Kollmorgen's named hybrid drawings. The same connector carries motor power and may carry brake wiring. Fit the correct factory cable and read the exact motor and drive diagrams before connecting.
| Motor connector option | SFD3 + | SFD3 − |
|---|---|---|
| D hybrid, AKM2G <20 A continuous | H | L |
| A legacy hybrid, applicable AKM2G 2–7 ≤20 A | C | D |
| J hybrid, AKM2G7 >20 A | 6 | 7 |
The D, A and J views in the manufacturer document show different power and brake contacts. The plus and minus above identify the combined feedback circuit. Use only the supported drive and cable for power and test. Kollmorgen hybrid motor connector pinouts (PDF)
Cables inside the motor and at the machine
For CA with the D SpeedTec connector and the AKD2G drive/current combinations shown in the Kollmorgen lookup (RMS <15 A in that row), the catalogue gives H2-21-015-A1-00-XXXX00 PUR and H6-21-015-A1-00-XXXX00 PVC patterns. Check the exact drive family and current rating and fill the length from the catalogue. The legacy A uses legacy AKM wiring. Internal sensor-to-board parts and machine-specific bulkheads require an OEM lookup. Kollmorgen SFD3 2G cable lookup (PDF) · Legacy A and alternate connector notes (PDF)
Fault checks
Isolate the complete hybrid circuit before unplugging it. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized. The hybrid connector carries drive power as well as feedback. Follow the manufacturer discharge procedure.
- Record. Capture the fault, recognized motor type, axis and feedback connector assignment before resetting. Compare the nameplate and full cable code.
- Inspect. Check the correct keyed shell, seating, loose pins, damaged seal, strain or coolant ingress. Check the motor and load for a separate coupling or mechanical issue while isolated.
- Test the disconnected cable. With the harness isolated from the encoder and receiver at both ends, use resistance mode. First short the meter probes to establish lead resistance. Check each conductor end to end and flex the cable gently at the strain relief. Check between unrelated wires and from signal wires to shield or shell. Expect open only where the drawing calls for isolation. Compare any intentional sense links or shield bonds with the equipment drawing. Keep insulation testers away from connected electronics. Use the exact hybrid cable drawing to identify the feedback pair, including its separation from phase and brake conductors.
- Isolate the path by substitution. On an approved drive and test setup, compare with a verified identical cable and intended port. If a known-compatible drive still fails to identify the motor after the cable path is verified, specialist internal evaluation is appropriate. Communication with an incorrect motor identity calls for checking firmware and stored configuration.
Motor and drive applications
For AKM2G servomotors built with CA SFD3. Confirm the drive's supported feedback input and hardware revision using the AKD2G manual. Separate SFD, SFD-M and HIPERFACE DSL options have their own drive requirements. Kollmorgen AKD2G feedback support · Motor-to-drive cable lookup (PDF)
Angle of alignment and commissioning
Capture motor identity, drive parameters, original feedback orientation and the verified motor-specific commutation reference before repair. Refer internal reinstallation, memory work and commutation verification to the matching Kollmorgen service procedure. After approved work, confirm correct identification, direction and commutation in a controlled test, then establish the machine datum separately. Kollmorgen stored motor data · AKM2G commissioning and documentation (PDF)
Drawings, pin maps and manuals
- Kollmorgen AKM2G Installation Manual (PDF). Motor code and feedback options, connector families and installation.
- Kollmorgen AKM2G motor connector pinouts (PDF). Separate A, D, E and J diagrams.
- Kollmorgen 2G cable lookup (PDF). Check motor and drive combination before ordering a hybrid.
- Kollmorgen AKD2G feedback types. Verify the intended drive interface and recognition.
- Mitchell Kollmorgen AKM support. Equipment-specific support boundaries.