What specialist testing can show
TI-5000JX bench. On the documented connection, check movement, index where fitted and commutation separately.
TI-3000JX motor run. Confirm the full motor order, power lead, phase reference and supported TI-3000JX setup.
Starting lead. TI-5701 for the documented 14-contact bayonet.
Lafert B6306P Tamagawa ABZ/UVW Servo Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| B6306P with Tamagawa ABZ/UVW | Mitchell TI-5701 branch. Capture the exact motor suffix and encoder label. |
| Lafert B3081 / Eltra EF80 | Separate documented branch with a 19-contact bayonet and different fitted encoder. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Motion | Incremental ABZ on the scoped B6306P fixture. |
| Commutation | UVW on the named test connection. |
| Connector | TI-5701, 14-contact bayonet. |
Interface and measuring method
Check position counts, index and commutation independently. Use the actual Tamagawa label and drive to establish output levels and resolution.
Mounting and fit
Record rear housing, rotor location and restraint before opening. Obtain the fitted Lafert and Tamagawa drawings before exchanging the encoder.
Wiring and connector scope
Match the 14-contact bayonet view and fitted circuit assignments. Confirm supply, returns and ABZ/UVW before choosing a test or replacement lead.
Internal motor and machine cables
Record the fitted encoder pigtail, bulkhead and drive cable separately. Check contact retention and shield termination against the original drawing.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Counts present, enable fault | Check UVW and original phase reference. |
| No feedback after harness replacement | Compare exact 14-contact pin map and fitted Tamagawa output. |
| Intermittent at motor connector | Check bayonet lock and disconnected harness. |
Angle of alignment and commissioning
Preserve original direction, index and motor phase reference. Follow the fitted motor procedure for any alignment or powered check.
Motor and drive applications
Lafert B6306P on the documented 14-contact bayonet branch
Find the correct B6306P harness and confirm the fitted Tamagawa order before exchanging the encoder.
Drawings, pin maps and manuals
- Mitchell Test Cable Index by Manufacturer Support. Lafert Support Part Numbers, TI-5701
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.