What specialist testing can show
TI-5000JX bench. Check serial ID and analogue channels on the matched LSN wiring.
TI-3000JX motor run. Confirm the full motor order, power lead, phase reference and supported TI-3000JX setup.
Starting lead. TI-5740 on the documented 17-contact M23.
LTI / Lust LSN Stegmann HIPERFACE Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| LSN with Stegmann HIPERFACE | Mitchell’s TI-5740 connection. Verify the fitted G6.x option and encoder label. |
| GH2 / GH3 | LTi G6.x cable-family codes. GH2 is listed for CDD3000 and GH3 for ServoOne. Confirm the full cable order. |
| FIP/FHP with ERN 1387 | Separate Lust/Stromag incremental branch with different signals. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback | Conventional HIPERFACE by fitted order. |
| Motor connection | 17-contact M23 in the Mitchell LSN entry. |
| OEM cable selection | Use the G6.x drive and cable table for the actual length, receiver and termination. |
Interface and measuring method
Check the digital identity and analogue movement signals separately. A serial response can be present while the analogue pairs have a wiring fault.
Mounting and fit
Use the exact LSN frame and encoder drawings. Check mounting seat, stator restraint and cable exit before disturbing the received reference.
Wiring and connector scope
Use the manufacturer G6.x connection drawing for the fitted motor and drive. Keep the motor-side and drive-side mating views separate.
Internal motor and machine cables
Match the complete GH2 or GH3 order to the actual drive. Record the internal encoder lead separately. TI-5740 identifies the shop fixture.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Valid ID with analogue tracking alarm | Trace the sine/cosine paths. |
| No data after changing drive cable | Compare GH2 and GH3 and check the fitted termination. |
| Dropout at the bulkhead | Inspect lock and strain relief and isolate-test the loom. |
Angle of alignment and commissioning
Record the original mechanical reference, direction and motor data where supported. Compare the replacement to the received configuration before commissioning.
Motor and drive applications
LTI/Lust LSN 17-contact M23 feedback branch
Identify the LSN feedback cable and compare serial and analogue faults independently.
Drawings, pin maps and manuals
- Mitchell Test Cable Index by Manufacturer Support. Lust Support Part Numbers, TI-5740
- LTi LSN servomotor catalogue. Supplementary reference for the stated model or setup.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.