Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
An isolated resistance check or a documented low-energy bench divider can help separate an element fault from wiring or PLC input trouble. Secure the wire and use a controlled displacement fixture. Treat any separate Mitchell capability as unverified for this passive sensor.
Micro-Epsilon WDS-1500-P60-CR-P-M4 Draw-Wire Position Sensor technical reference
Find your part number
Use the full label and suffix. The main reference is WDS-1500-P60-CR-P-M4. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| WDS-1500-P60-CR-P-M4 | 1,500 mm P60 draw-wire assembly. CR is fixed radial cable. Match the M4 wire attachment. | P is a passive potentiometric divider, with white/brown/green leads. |
| WDS P60 SR U / I | Separate family output options with a built-in radial plug. | Active voltage or current output. Use the separate SR wiring and power requirements. |
| WE-1500-M4 | Manufacturer-documented 1,500 mm mechanical wire extension with M4 connection. | Accessory for the application described by Micro-Epsilon. It carries mechanical displacement. |
Production and end-of-life status
Micro-Epsilon identifies this order code in its application note and documents the P60 family. Confirm current production and availability for the exact M4 build.
Specifications
| Parameter | Value and scope |
|---|---|
| Stroke | 1,500 mm for this sensor order. Use the specified usable travel and end-stop geometry. |
| Output | 1 kΩ ±10% passive potentiometric divider in the P output family. Use the sensitivity printed on the label. |
| Excitation | Manual lists maximum 32 V DC at the 1 kΩ / max. 1 W condition and wiper current up to 3 mA. Design within the actual resistance, power and temperature constraints. |
| Electrical lead | CR fixed radial cable, 1 m per P60 technical table. Follow figure 18 for colours. |
| Mechanical route | P60 manual allows up to 3° wire misalignment from the outlet axis. Use the prescribed pulley where needed. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Secure the sensor to the machine and align the outlet with the first wire run. Fasten the wire using the specified clip or M4 hardware. Use approved pulleys for direction changes and protect the run against abrasion and snagging. Verify that the target stays within the sensor's working stroke at both ends.
The measuring wire is spring-loaded. Support the moving assembly, secure the wire during handling and let it retract only under control. Keep personnel clear of the line of pull. Inspect pulley wear and sharp bends after the machine is isolated.
Interface and measuring method
Machine motion pulls a wire from a spring-return drum. The drum moves a potentiometer wiper. The controller supplies a reference across the two end terminals and measures the wiper voltage as a fraction of it. The input must have suitable impedance and the PLC or meter scale must match the sensor and reference. A supply change or cable drop can mimic a displacement error.
Verified wiring
Use figure 18 for the CR/P cable and figure 20 for the divider circuit. The active SR variants use different figures.
| Conductor | Function |
|---|---|
| White | Excitation input + |
| Brown | Ground / excitation return |
| Green | Wiper signal |
| Screen | Housing shield as shown in figure 18 |
Use the potentiometer as a divider. Keep wiper current within the manual's rating and follow the machine grounding diagram.
Cables inside the motor and at the machine
This build uses a fixed electrical lead. Order the controller extension by its documented shield, routing and terminal map. Micro-Epsilon lists WE-1500-M4 in its telescopic platform example. That is the separate mechanical wire extension. See the manual for approved guide pulleys when the installed routing requires them.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Wiper value flat or erratic | With the sensor disconnected from powered electronics and the wire secured, a qualified technician can check end-to-end element resistance and look for smooth wiper change during controlled travel. |
| Output scales incorrectly but moves smoothly | Compare excitation at the sensor, input loading and PLC calibration against known positions. |
| Reading jumps near the same point | Check wire routing, pulley friction and the wiper response at that location. |
| Wire slack or slow return | Inspect the route and fastening. Refer suspected drum or spring faults to the approved service procedure. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Micro-Epsilon documents this exact sensor and WE-1500-M4 extension for synchronized travel monitoring on telescopic platforms. Confirm the actual wire path, brackets and calibration from the machine drawings. The sensor provides position to the machine controller.
Angle of alignment and commissioning
Set wire geometry and mechanical stroke, then compare the sensor output at the OEM-defined reference positions. Record input voltage, end values and PLC scaling before changing hardware. Verify calibration after refit using the machine's permitted motion procedure.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- P output electrical ratings. Use the CR/P version and the listed rating conditions.
- Potentiometer circuit and wiring. Use figures 18 and 20 for this fixed-cable passive build.
- Exact Micro-Epsilon application and wire extension. Identifies the full model and WE-1500-M4 accessory.