What specialist testing can show
TI-5000JX bench. Mitchell documents the TI-5000JX OBA/OSA18 selection for HG-SR on the matched two-wire fixture.
TI-3000JX motor run. Verify the exact HG-SR motor and compatible modern two-wire run fixture independently.
Starting lead. Select TI-5658, TI-5732 or TI-5744 only after matching the fitted HG connector.
Mitsubishi Electric HG-SR MELSERVO-J4 22-Bit Serial Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| HG-SR | HG motor series covered in Mitchell’s J4 guide. Record the complete motor and amplifier orders. |
| OBA/OSA18 selection | Mitchell’s bench selection for the documented HG-SR 22-bit branch. |
| OBA/OSA24R markings | Mitchell reports these markings on some HG encoders. Verify the fitted label before choosing a replacement. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Drive-side resolution | 22-bit on the documented HG-SR J4 branch. |
| Serial data | Two-wire serial data on the HG connector generation described by Mitchell. |
| Fixture branches | Mitchell lists TI-5658 for 9-contact Tyco, TI-5732 for 10-contact DDK and TI-5744 for 17-contact MS within the HG family. |
Interface and measuring method
The amplifier gets digital position from the motor feedback. Tester profile names can refer to a compatibility mode. Compare the actual data reply, fitted label and motor generation before interpreting the displayed count.
Mounting and fit
Find the HG-SR frame and shaft drawing by complete motor order. Read the actual encoder label before disturbing the internal seat or harness. Preserve the installed shaft reference.
Wiring and connector scope
Use the Mitsubishi HG-SR motor and MR-J4 connection drawings and match the actual plug with the relevant Mitchell branch. Identify supply, return, serial data and any other circuits from the exact connector view.
Internal motor and machine cables
Use the motor and amplifier order to select the Mitsubishi encoder cable, including bend rating and length. Confirm the factory internal loom from the fitted encoder connector and assembly drawing.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| No serial data on the bench | Check the OBA/OSA18 selection, fitted plug and two-wire data path. |
| Communication drops during travel | Compare the short fixture with the full machine harness. Inspect cable strain and seating. |
| Position or reference changes after service | Verify full encoder suffix, drive configuration, saved reference and mechanical seating. |
Angle of alignment and commissioning
Save drive settings, position and alarm history before replacing feedback. Follow the matched Mitsubishi setup and reference recovery procedure. Confirm commutation and position on the installed motor before returning the machine to service.
Motor and drive applications
Mitsubishi HG-SR on MELSERVO-J4
Obtain complete HG-SR order, fitted encoder suffix, plug and exact machine and internal cables.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitsubishi HG Series Motors — MELSERVO-J4. Feedback Types and Connection Types
- Mitsubishi MELSERVO-J4 catalogue. HG-SR specifications and motor/drive combinations.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.