What specialist testing can show
TI-5000JX bench. TI-5000JX OBA13 profile with the documented lead selected by connector.
TI-3000JX motor run. Mitchell lists P4 and P8 OBA13 profiles for the corresponding fitted motor. Verify motor poles and fixture.
Starting lead. TI-5027, TI-5028, TI-5046 or TI-5620 according to the verified OBA13 connection.
Mitsubishi Electric OBA13 Legacy 13-Bit Serial Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| OBA13 | Mitchell lists 8,192 counts per turn and several connector-specific leads. Capture the complete label and motor order. |
| OBA / OBE construction | The Mitchell identification notes describe these as built-in arrangements. Confirm the actual shaft and encoder assembly. |
| OSA / OSE construction | Mitchell describes these as removable assemblies in its comparison. Match the real mounting and wiring before selecting a spare. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Serial resolution | 13 bits or 8,192 counts per turn on OBA13. |
| Retention | Mitchell documents a battery status bit on OBA13. Verify the fitted battery wiring and commissioning procedure. |
| Bench lead options | TI-5027, TI-5028, TI-5046 and TI-5620 in the OBA13 support table. Choose by actual connector. |
Interface and measuring method
The receiver reads serial position and status. Check the correct OBA13 profile and fitted connector before interpreting a failed reply or retention alarm.
Mounting and fit
Record the built-in assembly’s shaft engagement, encoder seat and cable route. Use the exact motor service drawing before disturbing components on the shaft.
Wiring and connector scope
Choose the lead from the OBA13 connector table. Verify supply, data, shield and any retention lines using the exact fitted connector view.
Internal motor and machine cables
Obtain the machine cable by actual motor and amplifier order. Keep the encoder-to-bulkhead loom separate from the test fixture and confirm both connector ends.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| No data with a similar Mitsubishi lead | Compare the OBA13 plug and lead option with the supported-types chart. |
| Battery alarm with valid position | Check the actual retention path and approved battery procedure. |
| Fault follows encoder installation | Verify the built-in assembly’s seating, fitted ID and original commutation. |
Angle of alignment and commissioning
Preserve the original machine and motor references. Verify the fitted pole count, installed position and reference recovery with the matched Mitsubishi procedure.
Motor and drive applications
Built-in OBA13 feedback, exact motor to confirm
Confirm fitted suffix, exact motor, lead, internal assembly drawing and retention cable.
Related SpareFaber guides
Drawings, pin maps and manuals
- Mitsubishi Motors and Serial Encoders. OBA13 position count, mounting and cable table
- Mitchell Mitsubishi supported encoder table. OBA13 resolution and scoped starting leads.
- Mitchell Mitsubishi Motors run chapter. P4/P8 OBA13 scope by exact motor.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.