Site visit or send-in evaluation
Provide the full encoder code and resolution, H8PS model, indicated position, machine datum and what changed before the fault. Include photos of the plate, connector and coupling. Use the enquiry form to share the details.
What specialist testing can show
A compatible parallel Gray-code receiver can display the decoded word while an approved bench fixture turns the shaft slowly. Verify every bit across a full turn, check the transition that repeats the fault and compare the same signals at both cable ends. Mitchell describes a generic parallel absolute test category. Confirm the exact interface cable, voltage, logic and support before using the TI-5000JX on this suffix. No exact TI-3000JX run-test combination is documented here. Mitchell parallel absolute feedback theory · OMRON E6F-A output circuits (PDF)
OMRON E6F-AG5C-C 256P/R Parallel Gray Encoder technical reference
Find your part number
Read E6F-AG5C-C 256P/R 2M. For this example, 256P/R means 256 absolute positions per turn, and 2M is the factory lead length. The last -C identifies the connector-ended version OMRON lists for the H8PS. Retain the resolution field when asking for a replacement.
| Full order code | Output | Termination / compatibility |
|---|---|---|
| E6F-AG5C-C 256P/R 2M | 8-bit Gray, NPN open collector | 2 m lead with H8PS connector. Main pin table below. |
| E6F-AG5C-C 360P/R 2M | 9-bit Gray, NPN open collector | H8PS connector. Different use of the upper bit contacts. |
| E6F-AG5C 256P/R 2M | 8-bit Gray, NPN open collector | 2 m pre-wired flying lead. Use the wire-colour table. |
| E6F-AG5B 256P/R 2M | 8-bit Gray, PNP open collector | Pre-wired lead and different receiver/logic requirements. |
| E6F-AB5C-C 360P/R 2M | BCD, NPN open collector | Connector version with a different code and pin map. |
OMRON E6F-A ordering and connection tables (PDF)
Production and end-of-life status
OMRON publishes the E6F-A lineup including the H8PS-specific code. Exact production or replacement status of the full resolution and cable code remains to be confirmed with OMRON. OMRON ordering lineup
Specifications
| Parameter | Value for the scope above |
|---|---|
| Position | 256 positions, 8 bits, Gray code. One code step is 360° ÷ 256 ≈ 1.406°. Code step is distinct from mechanical accuracy. |
| Power | 12 V DC −10% to 24 V DC +15%, up to 5% peak-to-peak ripple. 60 mA maximum encoder consumption. |
| Outputs | NPN open collector. 30 V DC maximum applied output voltage and 35 mA maximum sink current per output as specified by OMRON. Negative logic. |
| Response and shaft speed | 20 kHz encoder response frequency and 5000 rpm maximum permissible shaft speed. The positioner or machine may impose a lower limit. |
| Mechanical | Ø60 mm body, Ø10 mm solid shaft, Ø40 mm pilot, four M3 mounting holes per drawing. IP65 and −10 to +70 °C operation without icing. |
OMRON ratings, shaft drawing and notes (PDF) · H8PS encoder and response limits (PDF)
Mounting and fit
Use the face and pilot dimensions on the E6F-A drawing. The shaft takes a separate coupling. With the machine safely isolated, check the coupling fasteners, engagement and condition and look for radial or axial preload from misaligned shafts. An OMRON E69-C10B is the catalogued Ø10-to-Ø10 coupling example. Check both shaft diameters and machine space before ordering. Encoder and E69 coupling dimension drawings (PDF)
Interface and measuring method
This absolute encoder presents all eight position bits in parallel. In the specified Gray sequence, one bit changes between neighboring positions. The H8PS interprets that word as an angular position and switches cam outputs. A stuck high-order bit can cause a jump even when the shaft is smooth. Gray-to-position decoding and the specified negative logic matter. Counting one line with a pulse counter will miss the actual word. Gray output timing and negative logic (PDF) · H8PS positioner interface (PDF)
Verified wiring
Use OMRON's 8-bit (256) column under E6F-AG5C-C connector models. Identify contacts from the connector drawing. These assignments apply to the 13-contact RP13A-12PD-13SC connector with the original factory lead.
| Contact | OMRON assignment |
|---|---|
| 1 and 2 | Internally connected per OMRON's 256-position column. Follow the matching receiver wiring. |
| 3 | Gray bit 5 |
| 4 | Gray bit 1 |
| 5 | Gray bit 0 |
| 6 | Gray bit 7 |
| 7 | Gray bit 4 |
| 8 | Gray bit 2 |
| 9 | Gray bit 3 |
| 10 | Gray bit 6 |
| 11 | Shield / ground |
| 12 | 12–24 V DC encoder supply (nominal) |
| 13 | 0 V common |
For a spliced or non-original lead, establish the contact mapping with the disconnected harness and the manufacturer diagram before applying power. OMRON connector and flying-lead tables (PDF)
Cables inside the motor and at the machine
This is an external coupled unit with a factory 2 m cable. For H8PS installations, OMRON lists E69-DF5, E69-DF10 and E69-DF20 extensions of 5, 10 and 20 m. Match the two ends to the installed H8PS/encoder combination and check the restrictions in the H8PS documentation before extending. The machine has its own routing and shield practice. H8PS accessory list (PDF) · E6F-A connector and cable accessories (PDF)
Fault checks
Before unplugging, reaching the coupling or moving the shaft. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
- Record and inspect. Save the displayed angle, fault and cam settings. Under isolation, check the coupling, loose collars, connector latch, contamination, pushed contacts and the factory lead at its strain relief.
- Check the extension alone. With the harness isolated from the encoder and receiver at both ends, use resistance mode. First short the meter probes to establish lead resistance. Check each conductor end to end and flex the cable gently at the strain relief. Check between unrelated wires and from signal wires to shield or shell. Expect open only where the drawing calls for isolation. Compare any intentional sense links or shield bonds with the equipment drawing. Keep insulation testers away from connected electronics. Use the actual cable pinout. OMRON identifies an internal connection in the 256-position encoder, so take the encoder out of a harness-only continuity measurement.
- Check supply only under an approved energized procedure. A qualified technician can install a correctly pinned breakout while isolated, secure motion and measure 12 relative to 13 with the encoder connected. Use a compatible input load to observe the open-collector outputs. A handheld meter is suitable for static supply checks and can miss short dropouts or code transitions.
- Localize the error. Correct changes at the encoder with a stuck bit at the H8PS indicate the interconnect or input path. A smooth but offset reading calls for checking datum and coupling. Repeatable jumps at the same angle call for checking the corresponding bit and decode settings.
Motor and drive applications
OMRON documents the connector-ended E6F-AG5C-C with the H8PS cam positioner for machine timing. Confirm the H8PS position resolution and applicable response-speed limits. For an engineered PLC application, verify input type, Gray decoding and the sensor's output circuit against the PLC drawing. H8PS compatibility and commissioning (PDF)
Angle of alignment and commissioning
Use the machine's cam or shaft datum and the H8PS origin procedure. Record the coupling position, counting direction and approved cam program before removing the encoder. Restore the datum at the specified machine position and check output changes at controlled speed. There is no motor commutation adjustment for this external cam position encoder. H8PS origin and operation instructions (PDF)
Drawings, pin maps and manuals
- OMRON E6F-A datasheet (PDF). The connector and pre-wired assignments are separate. Check the resolution column.
- OMRON H8PS cam positioner (PDF). Encoder compatibility, cam origin, commissioning and extension-cable choices.
- OMRON E6F-A ordering lineup. Suffix, resolution and output-stage identification.
- Mitchell generic parallel absolute feedback. Use as test theory and confirm the exact cable before bench testing.