Identify the fitted part
| Guide scope | Panasonic MHMA202S1G / 176 mm flange — motor application |
|---|---|
| Feedback identity | MFE0017 |
| Main model / application identifier | MHMA202S1G |
| Motor order / source example | OEM catalogue order, not an inspected unit: MHMA202S1G |
| Interface | A4 17-bit Absolute/Incremental system |
| Starting connection | TI-5078 / TI-5074 / TI-5711 only where their drawing matches this exact motor; no universal Panasonic lead. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional TI-5000JX scope. 176 mm square flange; 2 kW, 200 V, 2000 rpm; key-way; without holding brake. Check seven-wire 17-bit feedback, battery path and incoming memory. Preserve original memory and retention/reference data; do not infer an offset solely from the catalogue motor code. |
|---|---|
| Starting lead / fixture | TI-5078 / TI-5074 / TI-5711 only where their drawing matches this exact motor; no universal Panasonic lead. |
| Profile / module | Preserve original memory and retention/reference data; do not infer an offset solely from the catalogue motor code. |
| TI-3000JX motor-run scope | Generic MFE serial run path is conditional. Verify actual motor winding, poles, power/brake connection, amplifier envelope, direction D:O and alignment. Size/power alone never establishes run capability. |
The documented test reference is Panasonic MINAS Motors — MINAS A4 identification table: MHMA + S feedback code; OEM exact order MHMA202S1G. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Panasonic marks this exact order discontinued. This does not establish present stock or a drop-in successor. Confirm current supply and the exact replacement with Panasonic, matching voltage, flange, shaft, brake, connector, feedback and motor-data requirements.
Specifications and interface
| Feedback technology | A4 17-bit Absolute/Incremental system |
|---|---|
| Motor flange | 176 mm sq. |
| Rated motor output (W) | 2000 |
| Motor voltage class (V) | 200 |
| Rated speed (r/min) | 2000 |
| Maximum speed (r/min) | 3000 |
| Rated torque (N·m) | 9.54 |
| Mass (kg) | 16.0 |
| Holding brake | without |
| Shaft | Key-way |
| Oil seal | with |
| Enclosure rating | IP65 |
| Enclosure exclusions | Except rotating portion of output shaft and connecting pin part of the motor connector and the encoder connector. |
| Connector arrangement | Connector |
| OEM encoder specification | 17-bit Absolute/Incremental system |
| Feedback branch | MFE0017 seven-wire, 17-bit serial feedback; preserve the absolute retention/battery circuit. |
| Voltage distinction | The motor voltage class is not the encoder supply voltage. Use the feedback connection drawing for the protected low-voltage supply. |
| Fit / service values | Exact shaft/coupling dimensions, pin map, tightening torque and service ID must match the fitted drawing; unverified values remain open. |
Establish the exact serial profile, count scale, startup behavior and retention arrangement. Some configurations combine serial startup with incremental running data; evaluate each path independently. Record initial status before a reset. A readable position does not verify mechanical coupling, compatible motor data or the complete drive system.
Mechanical fit and retention
Record the incoming shaft datum, locating seat, coupling, retaining cover, fasteners and cable exit before removal. After isolation, inspect accessible looseness, contamination, rubbing and bearing condition. Use the exact outline and service procedure for engagement, rear clearance and fastening. Do not import torque, air gap or coupling dimensions from a similar-looking motor. This order has a 176 mm square motor flange and Key-way shaft configuration. Flange width is not the encoder body diameter. Match shaft diameter, key dimensions, pilot, bolt pitch and rear clearance to the exact-order Dimensions tab before ordering. This exact order is without a holding brake; do not transfer rear-length or mass assumptions from a braked variant.
MHMA202S1G is the exact MINAS A4 Family catalogue order with a 176 mm square motor flange. 176 mm square flange; 2 kW, 200 V, 2000 rpm; key-way; without holding brake. MFE0017 Its S feedback character identifies MFE0017 seven-wire, 17-bit serial feedback; preserve the absolute retention/battery circuit. Preserve the complete suffix because voltage, shaft, brake and connector selections are not interchangeable across this family.
Wiring and connector boundaries
Separate the encoder plug, internal motor loom, bulkhead, machine cable and tester fixture. Verify contact numbering, keying, gender and drawing viewpoint. Identify supply/return, signal pairs, shield and independent temperature or brake paths from the exact diagram. Unverified pin assignments remain open. Identify the exact motor bulkhead and encoder-side connection before choosing a Panasonic test lead.
Starting connection for this guide: TI-5078 / TI-5074 / TI-5711 only where their drawing matches this exact motor; no universal Panasonic lead.. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
The fitted internal loom part number is not established by the motor family or protocol. Record both ends and obtain the motor assembly drawing. Machine cable selection also depends on receiver, length, shielding and fixed/flexing duty. A Mitchell test lead is not an OEM replacement cable number.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact assembly | MHMA202S1G is the exact MINAS A4 Family catalogue order with a 176 mm square motor flange. 176 mm square flange; 2 kW, 200 V, 2000 rpm; key-way; without holding brake. MFE0017 Its S feedback character identifies MFE0017 seven-wire, 17-bit serial feedback; preserve the absolute retention/battery circuit. Preserve the complete suffix because voltage, shaft, brake and connector selections are not interchangeable across this family. |
|---|---|
| Intermittent fault with cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, moisture and old repairs. Check continuity and unintended shorts against the exact diagram, accounting for intentional shield bonds. |
| No communication or usable signal | Confirm the fitted feedback, supported fixture and supply range. A qualified technician can compare source and load voltage with the approved breakout and OEM procedure. Connector shape alone does not establish a safe pin map. |
| Position reads but drive rejects the feedback | Check independent signal paths, motor identity, direction, index/retention and mechanical attachment. Record the original alarm and readable data before changing settings. A reset cannot establish compatible motor data. |
| Replacement motor looks similar | Compare the exact MHMA202S1G flange, voltage, shaft, brake, feedback character and connector against the proposed replacement. Family prefix and kW rating are insufficient. |
Alignment, reference and memory
Record the original mechanical reference, direction, motor phase convention, retained state and readable data before disturbing the feedback. Use the exact motor procedure for alignment and replacement. Electrical communication alone does not establish machine origin or correct motor/feedback pairing. Numerical alignment examples must stay with their stated motor, polarity and phase convention. Preserve readable motor memory and retention state before supported specialist work. Use the documented Generic MFE / D:O convention only after the exact motor, winding and fixture have been confirmed.
Motor and drive applications
A4 MHMA · 176 mm square flange; 2 kW, 200 V, 2000 rpm; key-way; without holding brake.. This guide is limited to the exact catalogue order and feedback branch shown above; check the actual fitted suffix and revision.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Panasonic MINAS Motors — MINAS A4 identification table: MHMA + S feedback code; OEM exact order MHMA202S1G
- Panasonic MHMA202S1G exact-order specifications — Spec Detail: flange, output, voltage, shaft, brake and feedback; Dimensions
- Panasonic MINAS A4 family catalogue — Use the stated family, option and document revision only
Obtain the fitted motor and encoder labels, exact service ID, internal loom/contact-view drawing and approved fixture. Match the linked manufacturer document to the exact order and revision.
Common questions
What should accompany a MHMA202S1G / 176 mm flange enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Generic MFE serial run path is conditional. Verify actual motor winding, poles, power/brake connection, amplifier envelope, direction D:O and alignment. Size/power alone never establishes run capability. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.