What specialist testing can show
TI-5000JX bench. Mitchell names the AS7Y SSI branch in the SEW table. Verify the exact SSI configuration, analogue path and safe fixture before testing.
TI-3000JX motor run. Confirm the actual DR motor and approved run arrangement. Record the applicable test scope for the fitted unit.
Starting lead. Verify an AS7Y SSI and analogue breakout for the actual connector.
SEW-EURODRIVE AS7Y DR71–DR132 SSI Multiturn Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| AS7Y | SEW spread-shaft multiturn SSI encoder in the Mitchell feedback table for DR71–DR132. |
| AS7W | Separate SEW RS-485 multiturn branch. See TCG150 for that application. |
| 13642944 | OEM AS7Y service-kit reference in the SEW catalogue. Check the fitted motor and encoder assembly before ordering. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Interface | Multiturn SSI and 1 Vpp sine/cosine on the documented AS7Y configuration. |
| Mounting | Spread-shaft arrangement in the DR71–DR132 reference. Match the motor shaft and mounting hardware. |
| Analogue scale | 2,048 periods in the SEW and Mitchell reference for the documented branch. |
Interface and measuring method
The drive clocks out absolute position over SSI and uses the separate analogue channels for motion tracking. A good SSI word can coexist with a damaged analogue pair or wrong scale.
Mounting and fit
Use the AS7Y installation drawing for spread-shaft seating, torque support and motor frame. Capture the original mechanical position and verify the matching kit against the motor order.
Wiring and connector scope
Use the AS7Y wiring diagram to identify the clock/data pairs, sine/cosine pairs, power and return. Match the exact motor terminal or plug and the cable end at the drive.
Internal motor and machine cables
Obtain the SEW encoder cable and any internal harness by the actual motor and drive order. Preserve the terminal or plug view and shield path. Confirm the test breakout by the exact connector.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| SSI reads and tracking is noisy | Inspect the analogue pairs and cable shield separately. |
| Drive reports no position after cable work | Verify AS7Y, SSI configuration and clock/data path. |
| Replacement changes count or direction | Check the fitted code, seating and drive reference. |
Angle of alignment and commissioning
Save the machine reference and drive setup. Verify the encoder’s mechanical seating, absolute position and analogue count after fitting under the SEW procedure.
Motor and drive applications
SEW DR71–DR132 with AS7Y
Confirm actual DR motor order, wiring view, service kit applicability and matched test fixture.
Related SpareFaber guides
Drawings, pin maps and manuals
- SEW Servo Motors. Feedback Type Codes, AS7Y in the absolute-encoder table
- SEW DR encoder product and technical data. AS7Y signal interface, motor frame and mounting.
- SEW encoder service kit table. AS7Y kit number and listed application.
- Mitchell-linked SEW feedback type table. AS7Y branch, interface and motor-frame scope.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.