What specialist testing can show
TI-5000JX bench. Check the analogue tracks and reference using the applicable 1 Vpp fixture and pin map.
TI-3000JX motor run. Confirm the drive input and feedback scale for the exact DR315 order.
Starting lead. Match the fitted 12-contact connection to the SEW EH7S drawing before selecting a fixture.
SEW-EURODRIVE EH7S / DR315 1 Vpp Hollow-Shaft Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| EH7S / DR315 | Hollow-shaft 1 Vpp sine/cosine option in the Mitchell-linked table. |
| EG7S | Separate plug-in shaft incremental option. Compare the rear mounting. |
| EH7T / EH7C | Other hollow-shaft EH7 output types in the OEM table. Match the signal code. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Analogue tracks | 1 Vpp A and B, 1,024 periods per turn, with a single C reference per turn in the cited SEW catalogue. |
| Supply | 10–30 V DC on the scoped EH7S. Follow the fitted OEM connection drawing. |
| Mechanics and plug | Shaft-centered hollow mounting and 12-contact connector in the cited branch. |
Interface and measuring method
The drive interpolates sine and cosine to obtain motion and direction. Check the signal amplitude and phase with the proper receiver or measurement, and verify the separate reference if the machine uses it.
Mounting and fit
Compare the hollow shaft, torque support and exact DR315 cover drawing. Record cable exit and the original position reference before loosening the encoder.
Wiring and connector scope
Use the SEW EH7S connector and mating view for the actual revision. Identify supply, returns and differential A/B and reference circuits before applying power.
Internal motor and machine cables
Verify the encoder pigtail and drive extension part numbers and shield connection. Match the contact arrangement before ordering a replacement harness.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Speed feedback fluctuates with valid supply | Check sine/cosine amplitude and the isolated cable. |
| One direction fails or is inverted | Compare A/B phase and drive selection. |
| Fault after mechanical service | Check hollow-shaft seating, torque support and rear clearance. |
Angle of alignment and commissioning
Record direction, mechanical reference and the actual drive scaling. Restore the shaft and housing location using the matched SEW procedure.
Motor and drive applications
SEW DR315, hollow-shaft EH7S option
Match the hollow-shaft EH7S fit and trace speed feedback using the DR315 drawing.
Drawings, pin maps and manuals
- SEW Servo Motors. Feedback Type Codes, Incremental encoders for DR motors, EH7S row, attachment 30646744512155
- SEW DR motor catalogue, EH7S encoder technical data. Supplementary reference for the stated model or setup.
- Mitchell-linked SEW incremental encoders for DR motors, EH7S row. Reference for the fitted feedback or motor option.
- SEW current option overview. Compare EH7S with other EH7 outputs and supported motor frames.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.