Identify the fitted part
| Guide scope | SEW-EURODRIVE CFM112M / BR / AK1H — motor feedback application |
|---|---|
| Feedback identity | AK1H; fitted label and connector to verify |
| Model / configuration identifier | CFM112M / BR / AK1H |
| Motor order scope | Documented frame, brake and feedback configuration; not a complete winding, thermal-sensor or connector order |
| Interface | AK1H multiturn HIPERFACE + 1 Vpp |
| Starting connection | TI-5650 + TI-5104 only at the matching 12-contact M23 motor-side HIPERFACE connection; direct encoders and terminal boxes require their own maps. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Named SEW CFM HIPERFACE evaluation with SEW motor-memory support; actual profile, supply, connector and fixture must match the fitted unit. |
|---|---|
| Starting lead / fixture | TI-5650 + TI-5104 only at the matching 12-contact M23 motor-side HIPERFACE connection; direct encoders and terminal boxes require their own maps. |
| Profile / memory scope | SEW motor-nameplate memory support; preserve original identity. Check retained revolutions independently. |
| TI-3000JX motor-run scope | Motor-run evaluation is conditional on the exact TI-3000JX motor/feedback profile, poles, phase order, alignment, power wiring, load restraint and amplifier envelope. A catalogue maximum or successful feedback bench test does not promise a full-rating run. Confirm the fitted brake circuit and controlled release before rotation. |
Mitchell names CFM with multiturn HIPERFACE; the OEM CFM71–112 encoder table explicitly identifies AK1H. Use the exact brake outline on printed page 109. Verify installed software, the actual sensor option and fixture before connection. A bench result describes the tested configuration; it does not clear the drive, machine cable or loaded axis.
Production and replacement status
The linked manufacturer document identifies this catalogue configuration. Current production, availability and any approved successor require confirmation against the complete fitted order. A downloadable manual does not prove present stock. Compare voltage, winding, mounting, shaft, brake, feedback, connector and stored motor-data requirements before accepting a replacement.
Specifications and interface
| Feedback technology | AK1H multiturn HIPERFACE + 1 Vpp |
|---|---|
| Frame / brake / feedback configuration | CFM112M / BR / AK1H |
| Motor square flange | 190 mm |
| Motor shaft diameter | 32 mm; see drawing for tolerances |
| Overall axial length including shaft | 496 mm, with BR brake |
| Outline reference | Printed page 109 of 19424019/EN, March 2017 |
| Order scope | Documented frame, brake and feedback configuration; not a complete winding, thermal-sensor or connector order |
| Feedback interface | AK1H multiturn HIPERFACE + 1 Vpp |
| Analogue periods per revolution | 1024; not retained revolutions |
| Supply reference | 7–12 V DC; verify the actual connection boundary |
| Feedback mechanical design | Conical-shaft feedback; exact fitted assembly and retention require confirmation |
| OEM encoder reference | Page 145: 0.9–1.1 Vpp sin/cos; 15-bit single-turn; 4096 multiturn revolutions; RS-485 serial data |
| Encoder electrical limits | 140 mA maximum current, 200 kHz maximum operating frequency; verify the fitted revision |
| Service values | Exact feedback coupling dimensions, pin map, tightening torque and permitted retention method require the fitted assembly drawing. |
AK1H combines serial absolute position with 1024 analogue sine/cosine periods per revolution. Evaluate serial communication, analogue track quality and within-turn movement independently. Verify retained revolutions with the supported multiturn profile. The 1024 figure counts sine cycles, not stored turns. This scope excludes HIPERFACE DSL and MOVILINK DDI. A mechanically close encoder with a different data profile is not established as interchangeable.
Mechanical fit and retention
Record the incoming shaft datum, pilot, bolt circle, rear clearance, cable exit and feedback retention before removal. Inspect play, debris, moisture and damaged contacts. Follow the exact assembly drawing for fits and fasteners; motor flange dimensions do not establish encoder coupling dimensions or tightening torque. Use the CFM112M brake outline on printed page 109. Its 190 mm flange and 32 mm shaft are independent dimensions. Verify pilot, bolt circle, shaft projection, rear housing and cable bend clearance from that same drawing. For AK1H the main BR drawing applies directly: LS = 496 mm. The 26 mm reduction belongs to RH1M and must not be applied to this AK1H configuration. Connector clearance and any hand-release arrangement still need separate checks. AK1H uses a conical-shaft feedback arrangement. The earlier AS1H spreading-shaft family is not a drop-in mechanical substitute; do not borrow its pin assignment or retention instructions.
CFM112M / BR / AK1H identifies a 190 mm square flange, 32 mm shaft and 496 mm overall axial length including the shaft, with BR brake. The complete winding, speed, thermal-sensor and connector suffixes remain to record from the fitted nameplate.
Wiring and connector boundaries
Keep motor power, protective earth, feedback and temperature circuits separate. Match contact numbering, keying, gender and mating-face versus wire-side view. A mechanically mating connector does not establish a pin assignment. The TI-5650 plus TI-5104 reference is for the matching 12-contact M23 motor feedback connection. A terminal box, different motor plug or direct encoder connection needs its own verified map. Test serial communication and the analogue tracks independently; a readable identity does not prove both signal paths are healthy. The AS1H diagram shown as a CFM example in Mitchell’s article does not establish the AK1H connector map. Obtain the actual AK1H wiring drawing before assigning contacts.
TI-5650 + TI-5104 only at the matching 12-contact M23 motor-side HIPERFACE connection; direct encoders and terminal boxes require their own maps.
The BR brake is a separate circuit from feedback. Its family code does not establish coil voltage, current, holding torque, release time or emergency-stop rating. Check the fitted brake label and OEM circuit, including the control and suppression components. Separate a failure to release or mechanical drag from a feedback fault. Never route brake power through the feedback fixture. Record release and re-engagement behaviour under an agreed, restrained test setup.
Internal loom and machine cables
Record the internal encoder-to-motor loom separately from the external machine cable and bench fixture. The internal loom part number is not established by the frame or interface alone. Obtain both connector faces, the assembly diagram and the correct contact view. Match cable length, shielding, temperature rating and fixed or flexing duty to the installation. A Mitchell test lead identifies a test connection; it is not an OEM replacement machine cable.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact configuration | CFM112M / BR / AK1H identifies a 190 mm square flange, 32 mm shaft and 496 mm overall axial length including the shaft, with BR brake. The complete winding, speed, thermal-sensor and connector suffixes remain to record from the fitted nameplate. |
|---|---|
| Intermittent fault during cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, contamination and earlier repairs. Compare continuity and unintended shorts against the correct diagram, accounting for intentional shield bonds. |
| Unstable position or missing feedback | Verify the actual sensor profile, matched excitation or DC supply, contact view and fixture. Inspect both analogue paths where applicable. A connector that mates mechanically can still have an incompatible pin assignment. |
| Position reads but the drive rejects it | Record the alarm, check the exact encoder identity and required motor data, then evaluate serial and analogue paths separately. A reset does not establish replacement compatibility. |
| Replacement dimensions look close | Compare this exact flange, shaft, feedback housing, brake and connector arrangement with the linked drawing. Do not use magnet-stack length, family digits or a similar power rating as the complete mounting envelope. |
| Holding, drag and load restraint | The BR brake is a separate circuit from feedback. Its family code does not establish coil voltage, current, holding torque, release time or emergency-stop rating. Check the fitted brake label and OEM circuit, including the control and suppression components. Separate a failure to release or mechanical drag from a feedback fault. Never route brake power through the feedback fixture. Record release and re-engagement behaviour under an agreed, restrained test setup. |
Alignment, reference and memory
Preserve incoming references and readable drive settings before disassembly. A smooth position reading alone does not prove electrical alignment or machine home position. Preserve the original SEW electronic nameplate and motor identity before a supported memory operation. SEW nameplate memory differs from the individual commutation offset workflow used by Allen-Bradley MPL. Mitchell describes a common SEW +U/−V 60-electrical-degree and +U/−W 120-electrical-degree convention for most applicable motors; match the fitted procedure and software rather than treating it as universal. Confirm mechanical reference, phase order and rotation direction, then check the machine datum independently.
Motor and drive applications
CFM112M / BR / AK1H identifies a 190 mm square flange, 32 mm shaft and 496 mm overall axial length including the shaft, with BR brake. The complete winding, speed, thermal-sensor and connector suffixes remain to record from the fitted nameplate.
Record the compatibility chain separately: complete motor order, actual feedback option, internal loom, bulkhead, machine cable and drive configuration. Similar power, a familiar connector shell or a shared protocol name cannot establish the whole chain. Any proposed replacement must also satisfy the mechanical, electrical and stored-data requirements of the specific machine.
Drawings, manuals and evidence
- Mitchell — SEW Servo Motors — Mitchell names CFM with multiturn HIPERFACE; the OEM CFM71–112 encoder table explicitly identifies AK1H. Use the exact brake outline on printed page 109.
- Mitchell — SEW Standard Alignment — Documented resolver examples; confirm the exact motor procedure
- SEW — CFM71–112, 19424019/EN (03/2017) — Brake outline, printed page 109; overall axial length includes shaft
- OEM feedback and package cross-check — CFM AK1H/EK1H encoder table, page 145
Source review: 20 November 2026. Obtain complete fitted motor and feedback labels, service ID, internal loom details and the correct connector mating-face drawing. Confirm the linked document revision and enabled test setup before extending replacement, wiring or motor-run claims.
Common questions
What should accompany a CFM112M / BR / AK1H enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Conditional on exact TI-3000JX motor/feedback profile, poles, phase order, alignment, power connection, restraint and amplifier envelope. Brake rating, control and release must be confirmed before rotation. No full-rating run capability is inferred from bench support. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
What a useful service record contains
Keep the incoming condition distinct from the result after cleaning, rewiring or adjustment. Record the exact alarm text, whether it appears at power-up or during motion, the direction and speed range involved, and whether temperature or cable position changes it. Include recent bearing, winding, feedback or drive-parameter work. These observations help decide whether a site visit can reproduce the fault or a detached assembly can answer the same question on the bench.
An evaluation report should identify the motor and feedback actually received, the tested connection boundary, selected profile, fixture, supply or excitation, and the observations obtained. Preserve the original memory report where applicable. Separate a confirmed defect from an unresolved condition and state any tests limited by missing drawings, mounting hardware or the machine itself. A repair recommendation should name the affected assembly and the evidence supporting it, with replacement availability and turnaround confirmed after inspection.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.