Identify the fitted part
| Guide scope | SEW-EURODRIVE CMP80M / AK1H — motor feedback application |
|---|---|
| Feedback identity | SEW AK1H conical-shaft multiturn encoder; verify fitted label |
| Model / configuration identifier | CMP80M / AK1H |
| Motor order scope | Frame/feedback configuration, standard motor without brake; not a complete winding order or inspected fitted unit |
| Interface | AK1H multiturn HIPERFACE + 1 Vpp |
| Starting connection | TI-5650 + TI-5104 only for the matched 12-contact M23 HIPERFACE connection. Other motor plugs, terminal boxes or direct-encoder connections require their own verified pin map. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional TI-5000JX named CMP AK1H feedback evaluation and SEW memory support, with exact installed profile, supply and lead. |
|---|---|
| Starting lead / fixture | TI-5650 + TI-5104 only for the matched 12-contact M23 HIPERFACE connection. Other motor plugs, terminal boxes or direct-encoder connections require their own verified pin map. |
| Profile / module | Read, decode and preserve SEW motor memory; verify serial multiturn position and analogue tracks separately. SEW nameplate memory does not contain an Allen-Bradley-style unique commutation offset. |
| TI-3000JX motor-run scope | Motor-run scope remains conditional on the exact motor/feedback profile, poles, phase order, alignment, power wiring, restraint and amplifier envelope. Frame size or bench support does not establish full-rating run capability. |
The documented test reference is SEW Servo Motors — Named SEW CMP AK1H synchronous absolute table; OEM drawing p.49; standard no-brake configuration. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
The linked manufacturer document identifies this catalogue configuration. Current production, availability and any approved successor require confirmation against the complete fitted order. A downloadable manual does not prove present stock. Compare voltage, winding, mounting, shaft, brake, feedback, connector and stored motor-data requirements before accepting a replacement.
Specifications and interface
| Feedback technology | AK1H multiturn HIPERFACE + 1 Vpp |
|---|---|
| Frame / feedback configuration | CMP80M / AK1H |
| Motor square flange | 138 mm |
| Motor shaft diameter | 28 mm; see drawing for tolerances |
| Overall axial length, including shaft | 322 mm; standard no-brake configuration |
| Brake scope | Without holding brake; braked versions require their own outline |
| OEM outline reference | Printed page 49 of the linked CMP catalogue 27799468 |
| Order scope | Frame and feedback option; complete winding and connector order not established |
| AK1H interface | Classic HIPERFACE multiturn with analogue sine/cosine tracks |
| Analogue periods per revolution | 1024; not the number of retained multiturn revolutions |
| Encoder supply reference | 7–12 V DC in the Mitchell AK1H table; confirm the actual connection boundary |
| Mechanical feedback design | Conical-shaft motor feedback; exact assembly and retention remain to verify |
| Service values | Exact encoder coupling dimensions, pin map and tightening torque require the fitted assembly drawing. |
AK1H combines multiturn serial absolute information with 1024 analogue periods per revolution. Check both signal paths, within-turn movement and retained turns with the supported profile. The 1024 figure is an analogue track count, not a statement about the multiturn capacity. This guide does not extend to HIPERFACE DSL or MOVILINK DDI. A mechanically close encoder with a different data profile is not established as interchangeable.
Mechanical fit and retention
Record the incoming shaft datum, pilot, bolt circle, rear clearance, cable exit and encoder retention before removal. Inspect play, debris, moisture and damaged contacts. Follow the exact assembly drawing for fits and fasteners; motor flange dimensions do not establish encoder coupling dimensions or tightening torque. Use the CMP80M outline on printed page 49. Its 138 mm flange and 28 mm shaft are independent dimensions. Verify pilot, bolt-circle, shaft projection and cable bend clearance from the same drawing. The AK1H housing adds the drawing’s 24 mm rear extension to the resolver base length of 298 mm, giving 322 mm overall. Retain this extra clearance behind the motor.
CMP80M / AK1H identifies a 138 mm square flange, 28 mm shaft and 322 mm overall axial length including the shaft in the standard no-brake drawing. This is a frame/feedback configuration; the winding, connector and any other fitted suffix still require the complete motor nameplate.
Wiring and connector boundaries
Keep motor power, protective earth, feedback and temperature circuits separate. Match contact numbering, keying, gender and mating-face versus wire-side view. Connector appearance alone is insufficient to establish a pin map. TI-5650 + TI-5104 only for the matched 12-contact M23 HIPERFACE connection. Other motor plugs, terminal boxes or direct-encoder connections require their own verified pin map. The named TI-5650 plus TI-5104 path applies to the matching 12-contact M23 motor feedback arrangement. A terminal box, a different motor plug or a direct encoder connection requires its own verified map. Assess serial communication and analogue sine/cosine tracks separately.
Starting connection for this guide: TI-5650 + TI-5104 only for the matched 12-contact M23 HIPERFACE connection. Other motor plugs, terminal boxes or direct-encoder connections require their own verified pin map.. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
Record the internal encoder-to-motor loom separately from the external machine cable and bench fixture. The internal loom part number is not established by the frame or interface alone. Obtain both connector faces, the assembly diagram and the correct contact view. Match cable length, shielding, temperature rating and fixed or flexing duty to the installation. A Mitchell test lead identifies a test connection; it is not an OEM replacement machine cable.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact configuration | CMP80M / AK1H identifies a 138 mm square flange, 28 mm shaft and 322 mm overall axial length including the shaft in the standard no-brake drawing. This is a frame/feedback configuration; the winding, connector and any other fitted suffix still require the complete motor nameplate. |
|---|---|
| Intermittent fault during cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, contamination and earlier repairs. Compare continuity and unintended shorts against the correct diagram, accounting for intentional shield bonds. |
| Unstable position or missing feedback | Verify the actual sensor profile, matched excitation or DC supply, contact view and fixture. Inspect both analogue paths where applicable. A connector that mates mechanically can still have an incompatible pin assignment. |
| Position reads but the drive rejects it | Record the alarm, check the exact encoder identity and required motor data, then evaluate serial and analogue paths separately. A reset does not establish replacement compatibility. |
| Replacement dimensions look close | Compare this exact flange, shaft, feedback housing, brake and connector arrangement with the linked drawing. Do not use magnet-stack length, family digits or a similar power rating as the complete mounting envelope. |
Alignment, reference and memory
Preserve the original mechanical reference, phase convention, rotation direction and readable drive settings before disassembly. Communication or a smooth position reading alone does not prove correct electrical alignment or the machine reference. Preserve the original SEW motor-nameplate and model data before any supported memory operation. This data has a different purpose from the unique commutation offset stored in an Allen-Bradley MPL encoder. Mitchell’s common SEW +U/−V 60-electrical-degree and +U/−W 120-electrical-degree convention applies to most, not all, relevant motors. Match the fitted procedure, mechanical reference and software before using it; do not import an Allen-Bradley memory workflow.
Motor and drive applications
CMP80M / AK1H; 138 mm square flange; Ø28 mm shaft; no brake. CMP80M / AK1H identifies a 138 mm square flange, 28 mm shaft and 322 mm overall axial length including the shaft in the standard no-brake drawing. This is a frame/feedback configuration; the winding, connector and any other fitted suffix still require the complete motor nameplate.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- SEW Servo Motors — Named SEW CMP AK1H synchronous absolute table; OEM drawing p.49; standard no-brake configuration
- SEW Standard Alignment — Named family and feedback option, rechecked 11 November 2026
- SEW-EURODRIVE CMP40–CMP112, 27799468/EN, November 2023 — RH1M resolver; pp.37,40,43 dimension drawings, standard motor without brake
Obtain complete fitted motor and feedback labels, exact service ID, internal loom and connector mating-face drawing. Confirm the linked document revision, fitted retention and enabled test setup before extending replacement, wiring or motor-run claims. SEW title is a frame/feedback configuration; complete winding and connector suffixes remain to record.
Common questions
What should accompany a CMP80M / AK1H enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Motor-run scope remains conditional on the exact motor/feedback profile, poles, phase order, alignment, power wiring, restraint and amplifier envelope. Frame size or bench support does not establish full-rating run capability. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.