Site visit or send-in evaluation
We can compare the absolute data and analog tracks, inspect the motor harness and establish what must be preserved before replacing the feedback unit. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Mitchell documents TI-5094 with the TI-5104 module for its SKS/SKM bench setup. Use the correct classic HIPERFACE selection to identify the unit and compare serial data with the analog tracks. Verify the exact motor harness and separately confirm any TI-3000JX run option.
SICK SKS36-HFA0-K02 1034095 HIPERFACE Single-Turn Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is SKS36-HFA0-K02. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| SKS36-HFA0-K02 / 1034095 | Tapered shaft, spring stator coupling, 8-pin radial encoder plug. | Single-turn HIPERFACE. 4,096 absolute positions and 128 sin/cos periods per turn. |
| SKS36-HFA0-K02-40 / 1131702 | SICK package listing identifies 1034095 as the included feedback unit. | Use the unit ID to find technical data and the pack ID to verify supplied parts. |
| SKM36-HFA0-K02 / 1034094 | Related SKM36 tapered-shaft family. | Multiturn version. Check drive selection, motor application and memory before substitution. |
Production and end-of-life status
SICK includes the exact model in its current technical material. Confirm exact-ID stock, ongoing production and any successor before ordering.
Specifications
| Parameter | Value and scope |
|---|---|
| Data path | HIPERFACE single-turn, 4,096 absolute steps per turn |
| Analog track | 128 sine/cosine periods per turn, 0.8 to 1.1 V peak-to-peak per SICK's signal diagram |
| Power at encoder | 7 to 12 V DC, recommended 8 V. 60 mA without load. |
| Mechanical speed | 12,000 min⁻¹ on the manufacturer’s mechanical specification |
| Fit | Tapered shaft with spring mounting plate and stator coupling |
| Environment | −20 °C to +110 °C. IP50 with the mating plug and cover fitted. |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
Match the SICK taper and spring-plate drawing to the motor. The central fastener secures the rotor, and the spring plate restrains the housing. On a locked-out motor, check the taper seat, standoffs and spring plate for rocking, distortion and witness marks. Keep the connector and harness clear of moving parts.
Use the tightening sequence and hardware for the actual motor and SICK mounting drawing. Verify the coupling can take up the specified movement without being bent or trapped.
Interface and measuring method
Classic HIPERFACE sends initial absolute position and parameter data on an RS-485 channel. Separate sine and cosine outputs and their individual references carry incremental motion. The drive uses both paths. A functioning data channel can coexist with noise or a bad reference on one analog track.
Verified wiring
Read the following cavity numbers on the encoder's 8-pin plug-in face, as drawn for the tapered-shaft SKS/SKM36. Use the correct connector drawing when looking into the mating cable. Keep the analog references and supply return identified separately.
| Pin | Signal |
|---|---|
| 1 | US, 7–12 V DC supply |
| 2 | +SIN |
| 3 | REFSIN |
| 4 | +COS |
| 5 | REFCOS |
| 6 | GND, supply return |
| 7 | Data+ |
| 8 | Data− |
Check housing and screen bonds against the SICK mounting and motor drawings. On analog tests compare +SIN to REFSIN and +COS to REFCOS with the documented load.
Cables inside the motor and at the machine
SICK DOL-0J08-G0M2XB6 (2031086) is a 0.2 m eight-wire loom, with the white 8-pin JST at the encoder and flying leads. Confirm the exact motor bulkhead, strain relief and approved shield treatment before terminating it. A PCB-to-M23 loom varies with the OEM assembly.
Mitchell's TI-5094 is the SKS/SKM direct-to-encoder lead in its MOOG application guide. Use the motor-specific harness drawing for in-motor or machine cables.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Data responds, motion feedback faults | Inspect the SIN and COS channels and both reference conductors with the approved receiver and loading. |
| Drive fails to identify the encoder | Check the loaded supply, serial pair, return and receiver selection before replacing the feedback unit. |
| Intermittent alarm after motor work | Inspect the white PCB plug, contacts, locating latch, bulkhead and cable routing. |
| Smooth feedback but startup torque is abnormal after a swap | Compare the mechanical seating, original motor data and verified alignment procedure. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Mitchell names SKS36 as a single-turn option on applicable MOOG motors. Verify the full MOOG motor and the fitted 1034095 label. Compare the SKM36 guide for the related multiturn family.
Angle of alignment and commissioning
Document taper seating and the original housing position. Where the motor OEM stores configuration or offset in encoder memory, read and verify the original data before removal. Restore it only through the OEM process for that same motor and a verified compatible encoder. The SICK model ID and mechanical drawing give the feedback specification. Obtain the motor’s commissioning procedure for angle and direction.
Drawings, pin maps and manuals
- Main technical PDF. Exact 1034095 datasheet. See pages 2–3 for specifications, 4–5 for mechanical and connector drawings, and the accessory section for the internal cable.
- Manufacturer reference. SICK SKS/SKM36 product selector and full type numbers.
- SICK SKS/SKM36 product information. Tapered-shaft plug-in face pin table, mounting variants and electronic type label background.
- SICK 2031086 loom datasheet. Eight-pin JST to flying leads.
- Mitchell MOOG motors guide. SKS36 application family, direct lead and module.