Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
A suitable resolver fixture can apply the documented AC excitation and compare both return amplitudes and decoded angle through controlled rotation. Confirm the correct Mitchell resolver adapter and excitation option for the exact build. Use the OEM motor test procedure for any powered run.
Tamagawa Smartsyn TS2620N21E11 Size 15 Resolver technical reference
Find your part number
Use the full label and suffix. The main reference is TS2620N21E11. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| TS2620N21E11 | Size 15 built-in resolver, 9.52 mm bore per the Tamagawa drawing. | 1X brushless resolver. Nominal 7 V RMS AC at 10 kHz and ratio 0.5 ±5%. |
| TS2620N691E126 | The manufacturer drawing lists a 10 mm bore. | Obtain the exact winding and receiver specification for the separate suffix. |
| TS2620N271E14 | A separate size 15 drawing and lead configuration. | Catalogue lists 10 V RMS AC at 4.5 kHz. Confirm ratio and drawing before replacing. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Rotor bore | Ø9.52 mm +0.015/0 in the Tamagawa drawing for N21E11. Compare the fitted shaft and nominal mounting position. |
| Excitation | 7 V RMS AC at 10 kHz, R1–R2, in the N21E11 catalogue column. |
| Conversion ratio | 0.5 ±5% for this exact model under the catalogue test conditions. |
| Accuracy | Maximum ±10 arcmin electrical error in the manufacturer table. Installation and receiver affect machine accuracy. |
| Environment | Catalogue built-in resolver operating range −55 to +155 °C. Verify the motor and harness limits. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
The rotor and stator fit directly into the motor assembly. Match the 9.52 mm bore and housing fit to the exact size 15 drawing. Set axial mounting dimension and radial alignment per the OEM assembly. Check that the stator cannot turn and the rotor clears it throughout a full safe rotation.
Interface and measuring method
The resolver converts shaft angle into two AC return channels. The receiver supplies the reference and demodulates the sine and cosine amplitudes. This 1X configuration yields one electrical cycle per mechanical revolution. Compare polarity, excitation and the machine's expected angle direction.
Verified wiring
Use the winding designations in the Smartsyn drawing. Identify the conductors using the exact label and connector schematic.
| Pair | Function |
|---|---|
| R1–R2 | AC excitation |
| S1–S3 | Cosine return |
| S2–S4 | Sine return |
Verify the output sign convention and connector orientation in the actual motor drawing. The catalogue gives AC impedance under specified conditions. A handheld meter reading in DC resistance mode has a different meaning.
Cables inside the motor and at the machine
Match the factory flying leads to the motor connector and receiver harness using the OEM wire list. Maintain pair twist, shielding and strain relief. Ask for the motor serial and bulkhead photo if an original loom number is required. Identify the position-feedback lead separately from motor phase or thermal wiring.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Both return channels low or missing | Check the reference under approved test conditions and verify the isolated reference pair from end to end. |
| One return channel absent | Check the disconnected harness and then the passive winding separately for continuity. Inspect the connector for shorts or pushed contacts. |
| Angle jumps after assembly | Check rotor seating and stator position, then compare the two return envelopes and polarity against known shaft motion. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
This is a built-in resolver for a motor or mechanism designed for its geometry, excitation and one-cycle feedback. Confirm the exact motor manufacturer and converter rather than applying another size 15 version's settings.
Angle of alignment and commissioning
Set mechanical fit per the drawing. The motor's commutation reference depends on its pole count, phase order and receiver. Record the fitted reference and perform the OEM electrical alignment in a controlled setup. Re-establish the machine datum separately if required.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Size 15 bore comparison drawing. Shows 9.52 mm N21E11 and the distinct 10 mm N691E126 variant.