Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
A qualified test can compare the master process data and diagnostics with measured angle using the correct target and gap. A head-only test without the positioning element leaves the mechanical path unchecked. Mitchell support is unverified for exact ID 1590975.
Turck RI360P0-QR24M0 IO-Link Contactless Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is RI360P0-QR24M0-IOLX2-H1141. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| RI360P0-QR24M0-IOLX2-H1141 / 1590975 | Separate positioning element and stationary QR24 sensor. Match the rotor and reducer to the shaft. | IO-Link 1.1, 32-bit process data. The head reports singleturn angle and a calculated turn count. |
| QR24 incremental output family | Related contactless housing concept. Verify position element and bracket. | Pulse output versions use a different receiver. The complete IOLX2 order code identifies the IO-Link variant. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Housing | 81 × 78 × 24 mm. IP68/IP69K per exact datasheet conditions. |
| Operating gap | 1.5 mm nominal spacing. Use the setup tools and LED guidance in the exact datasheet. |
| Supply / connector | 15–30 V DC, <50 mA. M12 × 1 4-pin male connector. |
| IO-Link | V1.1 COM2, 38.4 kbaud. 16-bit angle, 13-bit turns and three diagnostic bits in a 32-bit process value. |
| Rotor sizing | The separately selected positioning element and reducer determine shaft fit. The datasheet lists common metric and imperial sizes. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
The shaft turns a separate positioning element while the housing remains fixed. Check the exact shaft reducer and mounting bracket in pages 3–5. Set the rotor at the stated spacing with the proper mounting accessory. Check centering and clearance before removing the setup aid. Keep nearby metal or brackets clear of the sensing area as specified.
Interface and measuring method
The sensor couples inductively to its rotating element and converts the measured angle into an IO-Link process word. A compatible master uses the matching IODD to interpret angle, turns and diagnostics. Turck calls it semi-multiturn because turns are counted from zero crossings while powered. If the shaft can move during a power loss, check the turn-count plausibility diagnostic before using its multiturn value.
Verified wiring
Use the exact datasheet wiring diagram on page 1 and the master port diagram. This four-pin male M12 device uses pin 4 for IO-Link C/Q. Confirm L+ and L− using the numbered diagram before connecting the documented 15–30 V DC supply. Keep any unused contact in the specified state and verify the cable end-to-end mapping.
In an approved powered diagnostic setup, check that the master recognises the device and the physical port is configured for IO-Link. C/Q is a communication line. Use IO-Link diagnostics to interpret it.
Cables inside the motor and at the machine
Choose a compatible M12 A-coded sensor lead with the female device end and the correct master-port end. Preserve the documented C/Q path and supply rating. Order by length and installed routing. The position element and reducer order codes in pages 4–5 are mechanical accessories and are selected separately.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Master detects no device | Verify the port mode, 15–30 V supply and the pin 4 path. Check the device ID and IODD. |
| Data present but angular position drifts | Inspect rotor restraint, shaft fit and gap. Compare raw angle with the measured shaft angle through a controlled turn. |
| Angle sensible but total turns fail after power loss | Check the plausibility bit and whether the shaft moved while unpowered. Re-establish the machine reference using the approved procedure. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use on a shaft or rotary machine axis monitored by a compatible IO-Link master. Check PLC byte ordering and scaling in the IODD and the project's loss-of-position behavior.
Angle of alignment and commissioning
Set mechanical rotor position and gap, then document the angle zero, count direction and any stored preset. Restore the machine's reference only after validating the diagnostic bits and position through travel. This external encoder does not specify a motor commutation angle.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Exact product downloads. Use the matching IODD and accessories for order ID 1590975.