Site visit or send-in evaluation
Feedback diagnosis, Installation, Alignment. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Mitchell lists support for Sigma-7 serial 24-bit absolute encoders in Athena for TI-5000JX. Confirm the selected feature, exact wiring and allowable read operations. The motor-order evidence does not settle a TI-3000JX run profile.
Yaskawa SGM7J SGM7J-04A7A2C Sigma-7 Absolute Servo Feedback technical reference
Find your part number
Use the full label and suffix. The main reference is SGM7J-04A7A2C. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
SGM7J-04A7A2C identifies the complete Yaskawa motor. Its internal encoder model and revision are separate.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| SGM7J-04A7A2C | Sigma-7 SGM7J, 400 W class. Match the suffix, shaft and option drawing. | Feedback option 7 is 24-bit absolute. Record the fitted encoder label separately. |
| SGM7J with feedback code 6 | Different encoder option in the SGM7J ordering key. | 24-bit batteryless absolute. Check the applicable cable and drive setup separately. |
| UTTAI-B24 / UTTAH-B24RK21 | Sigma-7 feedback examples in Mitchell’s ID table, independent of this motor’s exact fitted encoder. | Use observed label and readback to establish the actual unit. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Motor order code | SGM7J-04A7A2C. 04 denotes 400 W and A denotes the 200 V motor class. |
| Position feedback | Code 7 is 24-bit absolute. Code 6 identifies the separate batteryless option. |
| Physical fit | Use the SGM7J-04A drawing for pilot, shaft and installed options. Encoder mechanical dimensions require the fitted unit’s service documentation. |
| Machine lead | Yaskawa publishes JZSP-C7PA0D-xx-E for specified toward-load battery/absolute and incremental arrangements in the SGM7J A5–10 frame group. |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
Keep the motor and encoder tags together. Support the axis independently of the brake and use the Yaskawa motor outline for mounting. Avoid disturbing the encoder reference before recording the axis direction and available service data.
Interface and measuring method
The SERVOPACK obtains position via the Sigma-7 serial encoder channel. Verify the configured absolute or incremental operating mode, along with the actual backup arrangement, before interpreting a restart alarm or exchanging encoder hardware.
Verified wiring
Use the exact Yaskawa encoder cable drawing and the installed SERVOPACK connector map. Identify supply, serial pair, shield and battery circuit only where documented. The 200 V motor class describes the motor power circuit. The feedback supply is a separate circuit.
Cables inside the motor and at the machine
JZSP-C7PA0D-xx-E is one documented external cable option for the SGM7J frame range, with the cited outlet direction and battery-capable wiring. Check the connector orientation, length and flex option before ordering.
Mitchell lists Sigma-7 serial bench support and cautions that the same encoder model can be wired in different ways. Confirm the fitted internal harness and tester adapter from both ends.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Absolute position lost after power down | Check the drive’s mode, alarm and documented backup path. Use the model-specific service procedure before disturbing a battery circuit. |
| Alarm began with cable replacement | Compare cable suffix, exit orientation, plug lock and battery wiring against the OEM cable drawing. |
| Motor identification reads but motion faults | Verify drive configuration, feedback direction and encoder reference with the Yaskawa procedure. Record whether the issue started after motor repair. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare the documented supply or excitation under the specified load. Use the approved receiver or instrument to observe the appropriate data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
This guide applies to the named SGM7J order on a compatible Sigma-7 SERVOPACK. Record the exact amplifier model and software, the motor option and the internal encoder label before using a test lead or transfer procedure.
Angle of alignment and commissioning
Record the established axis reference and any authorized encoder or drive records before disassembly. Verify the installed feedback reference and absolute initialization using the Yaskawa motor and SERVOPACK procedure. Mechanical and electrical offsets may be separate.
Drawings, pin maps and manuals
- Main technical PDF. Yaskawa Sigma-7 rotary servomotor product manual. Use the SGM7J ordering key, dimensions and encoder cable sections.
- Manufacturer reference. Match the exact order code or the identified motor option.
- Yaskawa JZSP-C7PA0D-xx-E drawing. One scoped external option. Match battery path and exit.
- Mitchell Yaskawa serial identification. Sigma-7 feedback examples and tester identification.
- Mitchell Athena release scope. Sigma-7 serial 24-bit absolute support.