Identify the fitted part
| Guide scope | Yaskawa SGMCS-17D3C11 — motor feedback application |
|---|---|
| Feedback identity | SGMCS 20-bit code 3; exact installed encoder label required |
| Main model / application identifier | SGMCS-17D3C11 |
| Motor order scope | OEM catalogue order, not an inspected unit: SGMCS-17D3C11 |
| Interface | 20-bit absolute serial, without multiturn data |
| Starting connection | Match the actual SGMCS flange/connector version; no universal direct-drive fixture assigned. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | TI-5000JX bench scope for the named Sigma family and 20-bit absolute serial, without multiturn data. Match the fitted label and enabled software, rotate slowly for count checks and use the exact connection drawing. Code 3 on this SGMCS means absolute singleturn without multiturn data; do not apply generic ABS battery/revolution-retention assumptions. |
|---|---|
| Starting lead / fixture | Match the actual SGMCS flange/connector version; no universal direct-drive fixture assigned. |
| Profile / module | Select the exact Yaskawa serial profile manually: Athena ENCODER ID may show ----. Mitchell does not support reading this encoder motor memory; preserve factory keying and use the exact motor/encoder identity for replacement. |
| TI-3000JX motor-run scope | No TI-3000JX motor-run support for Yaskawa serial encoders is offered in the current Mitchell testing article. This guide admits TI-5000JX feedback bench evaluation only; no motor-run capability is inferred. |
The documented test reference is Yaskawa Serial Encoder Identification — Mitchell SGMCS family and feedback code 3; OEM drawing A900-002-886. SGMCS OEM key overrides generic ABS multiturn assumptions.. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
The linked manufacturer record documents this configuration. Current production, stock and an approved successor for the complete fitted order still require manufacturer confirmation. A historical manual or downloadable CAD drawing does not prove present availability. Match voltage, mounting, shaft, brake, feedback, connector and motor-data requirements before ordering.
Specifications and interface
| Feedback technology | 20-bit absolute serial, without multiturn data |
|---|---|
| Exact catalogue order | SGMCS-17D3C11 |
| OEM drawing number | A900-002-886 |
| Motor voltage class | 200 V; not the feedback supply |
| Feedback code | 3: 20-bit absolute singleturn, without multiturn data |
| Shaft / brake / seal arrangement | 230 mm outer diameter; C-face non-load side |
| Rated torque | 17 N·m |
| Motor outer diameter | 230 mm; circular body, not a square flange |
| Service values | Encoder coupling dimensions, exact pin map and tightening torque require the fitted assembly drawing. No value is inferred from a related motor. |
The OEM SGMCS code table explicitly describes code 3 as 20-bit absolute without multiturn data. This exact construction limits the broader terminology used in general Yaskawa serial testing notes. A tester revolution display is not evidence of retained machine turns.
Mechanical fit and retention
Record the incoming shaft datum, pilot, bolt pattern, rear clearance, cable exit and retaining arrangement before removal. Use the exact drawing for tolerances and fastening. Do not infer encoder coupling dimensions or tightening torque from the motor flange size. Inspect looseness, bearing play, debris and moisture before disturbing the feedback attachment. This 230 mm outer-diameter direct-drive motor requires the exact C-face, hollow centre, bolt pattern and load-interface drawing. 230 mm outer diameter; C-face non-load side. Preserve the load-side/non-load-side distinction. Support the attached load independently and keep the motor and encoder assembly restrained during inspection.
SGMCS-17D3C11 is the exact catalogue configuration identified by OEM drawing A900-002-886. 17 Nm; 230 mm outer diameter; C-face non-load side. Check 20-bit absolute position without multiturn data and the direct-drive mounting. The drawing describes a catalogue order, not an inspected customer motor.
Wiring and connector boundaries
Keep motor power, protective earth, feedback, temperature sensing and any holding brake as separate circuits. Establish contact numbering, keying, gender and whether the drawing shows the mating face or wire side. Do not infer a pin map from a connector shell. The exact OEM drawing and actual connector face must select the test lead. Match the actual SGMCS flange/connector version; no universal direct-drive fixture assigned. The drawing document number is not an encoder service part number. Confirm the feedback supply and contact view from the matched cable drawing before connection.
Starting connection for this guide: Match the actual SGMCS flange/connector version; no universal direct-drive fixture assigned.. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
Record the internal encoder-to-motor loom separately from the external machine cable and test fixture. The internal loom part number is not established by the motor model alone. Obtain the assembly drawing and both connector faces. Match cable length, shielding, temperature rating and fixed or flexing duty to the installation; a Mitchell test lead is not an OEM replacement cable.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify before testing | SGMCS-17D3C11 is the exact catalogue configuration identified by OEM drawing A900-002-886. 17 Nm; 230 mm outer diameter; C-face non-load side. Check 20-bit absolute position without multiturn data and the direct-drive mounting. The drawing describes a catalogue order, not an inspected customer motor. |
|---|---|
| Intermittent fault with cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, contamination and previous repairs. Compare continuity and unintended shorts with the exact diagram, allowing for intentional shield bonds. |
| No serial data or unstable position | Confirm the profile, low-voltage supply at the correct boundary and mating-face pin assignment. Compare the test fixture with the actual motor connector; a plausible connector fit does not prove electrical compatibility. |
| Feedback reads but the drive rejects it | Record the original alarm and check exact motor identity, stored data requirements, direction, mechanical attachment and the supported signal paths. A reset is not proof of a compatible replacement. |
| Replacement dimensions look close | Compare the exact model, shaft, pilot, brake, seal, cooling and connector options above with the linked drawing before ordering or removing the original assembly. |
| Athena identity appears blank | A ---- identity display is expected in the documented support. Select the profile from the fitted motor/feedback identification; do not claim that Athena read or confirmed the stored motor model. |
Alignment, reference and memory
Preserve the original mechanical reference, motor phase convention, direction and readable drive data before disassembly. Use the fitted motor and encoder service procedure for replacement. Communication alone does not prove correct alignment or machine origin. This code-3 SGMCS configuration provides absolute singleturn position without multiturn data. Do not diagnose it by a generic retained-turn or battery test. The direct-drive mechanical reference and exact encoder mounting control replacement; no unverified pole count, run fixture or universal alignment angle is supplied.
Motor and drive applications
SGMCS · 17 Nm; 230 mm outer diameter; C-face non-load side. Check 20-bit absolute position without multiturn data and the direct-drive mounting.. SGMCS-17D3C11 is the exact catalogue configuration identified by OEM drawing A900-002-886. 17 Nm; 230 mm outer diameter; C-face non-load side. Check 20-bit absolute position without multiturn data and the direct-drive mounting. The drawing describes a catalogue order, not an inspected customer motor.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Exact OEM outline drawing A900-002-886 — SGMCS-17D3C11
- Yaskawa Serial Encoder Identification — Mitchell SGMCS family and feedback code 3; OEM drawing A900-002-886. SGMCS OEM key overrides generic ABS multiturn assumptions.
- Yaskawa Serial Encoder Testing — Named motor family and feedback option; row locator identifies scope
- Yaskawa Sigma-5 Rotary Servomotors, YEA-KAEPS80000042L — SGMGV, SGMSV and SGMCS model keys and external dimensions
- Yaskawa Direct Drive Servomotors catalogue, model designations — SGMCS p.85: code 3 is 20-bit absolute WITHOUT multiturn data; diameters and flange codes
- Yaskawa SGMCS-17D3C11 dimensional drawing A900-002-886 — Document title, description, PDF and DXF download; exact motor order
Obtain the complete fitted motor and encoder labels, exact service ID, internal loom, connector mating-face drawing and approved setup. Match the linked OEM document revision; unverified supply, pins, retention fasteners and alignment values remain open. Yaskawa serial TI-3000JX run and encoder-memory reading remain unsupported in the checked Mitchell article.
Common questions
What should accompany a SGMCS-17D3C11 enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
No TI-3000JX motor-run support for Yaskawa serial encoders is offered in the current Mitchell testing article. This guide admits TI-5000JX feedback bench evaluation only; no motor-run capability is inferred. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.