Site visit or send-in evaluation
On site, we trace the resolver excitation and returns through the motor cable. Bench evaluation can compare winding and signal behaviour with a known reference when the assembly data are available. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
An approved resolver bench setup can measure the excitation and compare sine/cosine amplitudes and phase as the shaft moves. A winding check uses the OEM resistance criteria with the resolver disconnected from its receiver. Keep the supply off until the excitation specification and pin map are verified.
TI-5901 identifies the family-level lead. Verify the exact resolver module and test profile before a TI-5000JX check, and independently verify motor run support and fixtures for TI-3000JX.
ABB Baldor RF0001 One-Speed Brushless Resolver technical reference
Find your part number
Use the full label and suffix. The main reference is RF0001. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| RF0001 | One-speed brushless resolver on BSM80C-4150AA. Baldor OEM part number. | Analog excitation and two return windings. Supplier ordering code is open. |
| OE0323A02 | Different feedback assembly on BSM80C-275RF. | ABZ/UVW encoder with a 16-pin feedback outlet and a different test path. |
Production and end-of-life status
The OEM parts list identifies RF0001. Confirm the exact service part’s supply and supersession status with Baldor for the motor serial number.
Specifications
| Parameter | Value and scope |
|---|---|
| Resolver type | Brushless, one speed, from Baldor's BSM80C-4150AA parts list |
| Listed resolver diameter | 1.4165 in, approximately 36.0 mm. Verify fit and tolerances on the actual resolver drawing. |
| Motor feedback connector | WD1455A01, M23 threaded, 12-pin on the documented motor |
| Motor-side lead | LD2200A08 is listed with the resolver in the same bill of materials. |
| Electrical data still needed | Exact excitation amplitude and frequency, transformation ratio, winding resistance and connector pin assignments |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
The Baldor packet lists a C-shaped resolver clamp in the BSM80C assembly. The resolver diameter helps identify the unit. It does not determine the shaft register, rotor retention, clearance or clamp setting. Before removing anything, record the original rotor/stator relationship, location and orientation.
On an isolated motor, look for witness marks, clamp movement or evidence of rubbing. Compare the housing and connector placement with the Baldor outline. Use the OEM service drawing to set the internal fit.
Interface and measuring method
The receiver excites a reference winding with an AC carrier. The two return signals vary with shaft angle, and the receiver decodes their ratio and signs. One speed means one electrical position cycle per mechanical revolution. Open excitation can take out both returns, so check that path before attributing two missing outputs to the resolver.
Verified wiring
Identify the excitation pair, sine return pair, cosine return pair and the shield termination from the exact motor wiring sheet. The published parts list establishes the 12-pin M23 connector identity. It does not assign the individual cavity numbers. Match the drawing view and harness at the motor and the drive before applying excitation.
| Circuit | Check |
|---|---|
| Excitation | Verify the OEM carrier requirement and the receiver’s excitation path. |
| SIN / COS | Check each differential winding pair with the documented polarity. |
| Shield and shell | Verify the specified bonds on the actual harness. |
Cables inside the motor and at the machine
The BSM80C-4150AA bill of materials names LD2200A08 and the WD1455A01 feedback socket. Confirm the serviceability of the lead and actual pinout with Baldor using the motor spec. Mitchell lists TI-5901 for the BSM 12-pin M23 resolver family. Confirm the fitted motor wiring before connecting it.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Both returns missing | Confirm drive excitation arrives at the motor and the common connector path is intact. Verify the receiver setup. |
| Only one return is absent or unstable | With the harness isolated, check the corresponding pair, crimp and shorts. A specialist can compare the two modulated returns under approved excitation. |
| Repeatable angle error after motor repair | Check resolver retention, return polarity, direction and the drive’s commutation reference before condemning the windings. |
| Fault follows temperature or movement | Record conditions and check cable strain, connector retention and motor mechanical play. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Baldor spec S2P166W071 for BSM80C-4150AA documents this resolver. The BSM name also appears on encoder-equipped builds, including BSM80C-275RF with OE0323A02. Match the motor's order code, connector and drive feedback selection.
Angle of alignment and commissioning
The resolver is passive. Motor commutation depends on the installed mechanical relationship, winding polarity and receiver setup. Capture the original reference before moving the stator or rotor. The exact Baldor setting and verification method are needed before replacing or rotating the assembly.
Drawings, pin maps and manuals
- Main technical PDF. Parts list and outline for BSM80C-4150AA, spec S2P166W071.
- Manufacturer reference. Baldor motor catalogue reference for the documented RF0001 build.
- Mitchell manufacturer cable index. Baldor BSM TI-5901 entry and connector family.
- Mitchell training manual. Resolver measurement background and test-platform documentation.