What specialist testing can show
TI-5000JX bench. Check serial identity and the analogue tracks separately. Confirm the Fagor memory scope for the fitted motor.
TI-3000JX motor run. Confirm the full motor order, power lead, phase reference and supported TI-3000JX setup.
Starting lead. Match the fitted FKM connector. TI-5063 is indexed for the Fagor 12-contact HIPERFACE branch when the map agrees.
Fagor / SICK Stegmann FKM E3 / SRS50 SinCos HIPERFACE Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| FKM E3 · SRS50 | Singleturn SinCos option on the cited Fagor table. Check the taper and stator restraint. |
| Older FKM E3 SRS | The same catalogue lists an earlier rubber-flange version. Verify the original fit. |
| FKM A3 / R0 | Multiturn SRM or resolver options. Match the feedback position in the order. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Position tracks | 1,024 periods per turn on the cited E3. |
| Connection | The Fagor HIPERFACE cable entry lists TI-5063, 12-contact M23. Confirm the fitted FKM wiring before use. |
| Mechanical fit | Tapered shaft and the applicable stator restraint on the exact OEM assembly. |
Interface and measuring method
Conventional HIPERFACE combines analogue motion tracks and a serial channel. Read the identity and check analogue response separately. Use the actual Fagor profile for any motor data.
Mounting and fit
Compare the taper and stator support with the fitted drawing. Record housing position, encoder orientation and cable exit before loosening the center fixing.
Wiring and connector scope
Use the complete FKM motor and drive orders to identify connector view and pin map. Match the analogue, serial and supply circuits before testing.
Internal motor and machine cables
Trace the SRS pigtail to the motor bulkhead and identify the machine extension separately. Check the exact contact layout rather than relying on M23 shell size.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Serial identity reads but motion alarm persists | Check sine and cosine paths on the matched connection. |
| Fault after replacing an older E3 | Compare taper, restraint and original encoder order. |
| Feedback drops when the cable bends | Check plug lock, harness strain and isolated continuity. |
Angle of alignment and commissioning
Preserve the original reference, direction and any supported motor data. Compare original and replacement order and fit before applying Fagor commissioning steps.
Motor and drive applications
Fagor FKM E3 feedback option
Check the E3 taper and stator restraint. The Fagor manual distinguishes the sheet-metal version from an older rubber-flange E3.
Drawings, pin maps and manuals
- Mitchell Product Catalog, TI-5000JX supported feedback. Mitchell Fagor motor and SRS/SRM listing, with Fagor FKM E3 order mapping
- Fagor DDS servo drive system manual, FKM sales reference. Supplementary reference for the stated model or setup.
- Mitchell test cable index, Fagor section. TI-5063 Fagor HIPERFACE cable entry. Match the actual FKM connection.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.