Site visit or send-in evaluation
Share the feedback label, complete motor or machine order, drive model and alarm. Include both connector faces and note whether the issue followed a cable change, replacement or mechanical work.
What specialist testing can show
TI-5000JX bench. Mitchell lists the αiA4000 high-speed profile. Match the two-wire motor connection before using TI-5750.
TI-3000JX motor run. Mitchell documents a high-speed FANUC run selection. Confirm the exact A06B motor, power cable and supported run settings separately.
FANUC αiA4000 A860-2050-T321 High-Speed Serial Pulsecoder technical reference
Find your part number
Use the full fitted label. A motor order identifies the assembly and should be recorded separately from an encoder part number.
| ID or order code | Identification and scope |
|---|---|
| A860-2050-T321 | αiA4000 high-speed serial pulsecoder listed in the FANUC connection manual. |
| αiA4000 | Profile and family designation. Use the full A860 code to identify the fitted assembly. |
Production and end-of-life status
Confirm current orderability and any successor for the exact ID with the manufacturer or motor OEM. The dated documentation identifies the configuration.
Specifications
| Parameter | Verified scope |
|---|---|
| Interface | FANUC high-speed serial in the αiA4000 family. |
| Position | Absolute pulsecoder. Use the CNC and servo amplifier documentation for the reference and retention procedure. |
| Connector | Match the A06B motor order, pulsecoder revision and external feedback harness. |
Mounting and fit
Read the A06B motor order and the full A860 pulsecoder label. Record coupling orientation and any damage or play before removing the feedback cover. Use the exact FANUC service drawing for the rotor fit and retention.
Interface and measuring method
Mitchell describes the high-speed data path as a two-wire RD pair. The legacy four-wire data connection uses separate request and data pairs. A legacy test harness can give a no-response result on a healthy high-speed device.
Wiring and connector scope
Use the matching motor and amplifier connector diagrams. Confirm the physical connector view and wire population, then compare the approved RD pair, supply and return. The tester connector diagram applies to the test lead and cannot establish the internal encoder wiring.
Cables inside the motor and at the machine
TI-5750 is the Mitchell lead for the documented two-wire high-speed connection. TI-5047 applies to the older four-wire connection. Confirm the A06B order and service cable label before selecting either.
Fault checks
Before inspection. Follow the site’s isolation and lockout procedure. Secure any load against movement, allow the specified discharge time and have a qualified technician verify isolation. Check resistance on a disconnected harness at both ends. Use the documented shield and return connections.
| Observation | What to verify |
|---|---|
| No response on the legacy harness | Verify the high-speed profile and the correct two-wire connection before rejecting the pulsecoder. |
| Position reads but the CNC reports a reference alarm | Review the OEM battery and reference procedures for that axis before clearing any data. |
| Alarm follows work on the rear cover | Inspect the encoder harness, coupling and seating using the A06B drawing. |
Motor and drive applications
FANUC αi. Exact A06B order open. Check the exact ID, drive and connector before applying an installation or test procedure.
Match the T321 pulsecoder to the motor order and amplifier before choosing a harness or reference procedure.
Angle of alignment and commissioning
Record the current axis reference and drive configuration before teardown. After service, use the exact CNC and motor procedure to recover the machine datum and verify motor feedback alignment. Keep absolute-reference recovery separate from the encoder communication check.
Drawings, pin maps and manuals
- Athena support notes. TI-5000JX New Encoder Support. Alpha A4000i.
- Mitchell FANUC high-speed support. Legacy and high-speed data pairs, TI-5750, and separate run selection.
- FANUC B-64483EN-2 reference copy. The pulsecoder table associates αiA4000 with A860-2050-T321.