What specialist testing can show
TI-5000JX bench. Use TI-5094 and TI-5104 for the documented EMME-AS direct-to-encoder configuration after verifying the fitted connection.
TI-3000JX motor run. Confirm the actual motor order, alignment and any applicable run profile.
Starting lead. TI-5094 on the matching direct encoder plug in the Festo article. Module TI-5104 on the verified direct encoder setup.
Festo EMME-AS-40-S-LV-AS Singleturn HIPERFACE Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| 2082428 / EMME-AS-40-S-LV-AS | Festo’s exact short-frame, low-voltage, singleturn motor order. |
| 2082429 / EMME-AS-40-S-LV-AM | Multiturn configuration on the same motor size. Compare the drive setup and position retention before a replacement. |
| EMMS-AS / EMMT-AS | Separate motor families in Mitchell’s article. Their test connectors and feedback types depend on the order. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Encoder measuring method | Capacitive sensing with classic HIPERFACE. |
| Position and tracks | Festo specifies 12-bit typical resolution and 16 sine/cosine periods per revolution for item 2082428. |
| Accuracy | 20 arcmin typical rotor-position accuracy in the 2082428 motor data sheet. |
| Cable access | Mitchell describes a documented direct-to-encoder route for applicable EMME-AS units. Confirm the fitted plug. |
Interface and measuring method
The drive reads absolute position within one turn over HIPERFACE and tracks the analogue sine/cosine signals during movement. A 12-bit position value and 16 physical analogue periods describe different properties.
Mounting and fit
Use Festo’s 2082428 motor drawing for the external envelope and the fitted rear assembly documentation for encoder seating. Record the rotor reference and cable exit before removal. Verify the exact internal encoder assembly rather than matching the housing from a photograph.
Wiring and connector scope
Use the item-specific Festo motor connection and identify the fitted internal feedback plug. Check the serial data and analogue pairs on the matching drawing before using the direct test fixture. Keep the motor winding and any thermal circuit separate.
Internal motor and machine cables
Select the Festo feedback cable from the drive and motor combination in the EMME-AS catalogue. The internal encoder lead is a separate assembly. TI-5094 is a Mitchell test lead for the documented direct connector.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| The drive identifies feedback but trips during motion | Check the sine/cosine circuit and connector strain before replacing the sensor. |
| Correct motor size with wrong turn behavior | Check AS or AM at the end of the motor order and the drive’s feedback selection. |
| No serial reply | Confirm the fitted direct plug, supply and data path before judging the encoder. |
Angle of alignment and commissioning
Record the received electrical reference and drive feedback configuration. After fitment, verify feedback direction and reference with the correct drive and Festo procedure. An angle needs the motor order and phase convention.
Motor and drive applications
Festo EMME-AS size 40, AS
Identify the AS singleturn option and choose its feedback and mounting documents.
Related SpareFaber guides
Drawings, pin maps and manuals
- FESTO EMME-AS, EMMS-AS and EMMT-AS Series. EMME-AS feedback and direct encoder setup
- Festo EMME-AS catalogue. Motor sizes, option codes and motor-to-drive cable ordering.
- Festo item 2082428 data sheet. Exact motor order and capacitive singleturn feedback specifications.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.