Site visit or send-in evaluation
Send the full encoder ID and line count, shaft and connector photos, motor or machine order code, drive model and alarm. Note whether the fault follows speed, cable motion or recent mechanical work. On site, the engineer can check the installation and drive input. Bench evaluation can separate encoder behavior from the machine harness and help determine repair options. Enquire about your installation.
What specialist testing can show
With a correctly terminated 1 Vpp input, a specialist can check A/B amplitude and phase, direction, periods per turn and the reference pulse while the shaft turns on a guarded fixture. HEIDENHAIN documents 1 Vpp inputs on its PWM 21. Mitchell documents the TI-5101 for 5 V, 1 Vpp measurements in its technical notes. Confirm the ERN 480 bench profile, lead and setup with Mitchell before using TI-5000JX. TI-3000JX running depends on the complete motor and matched setup. ERN 480-specific running support remains unverified. HEIDENHAIN PWM 21 product information (PDF) · Mitchell 1 Vpp measurement notes.
HEIDENHAIN ERN 480 technical reference
Find your part number
Read the complete ID NR. on the label. The 385480 prefix is the ERN 480 family in the catalogue. The suffix selects a build. Compare the full ID for bore, cable outlet and line count before ordering. All five records below specify coupling type 14 on a Ø63 mm bolt circle, D294999 signal assignment and 5 V DC ±10%.
| Full manufacturer ID | Lines per turn | Shaft fit | Encoder connection |
|---|---|---|---|
| 385480-40 | 2048 | Ø12 mm through bore, 70C | 27S12 radial M23 flange socket |
| 385480-42 | 2048 | Ø12 mm blind bore, 24 mm deep, 68A | 27S12 axial M23 flange socket |
| 385480-48 | 1024 | Ø12 mm through bore, 70C | 27S12 radial M23 flange socket |
| 385480-02 | 1024 | Ø12 mm through bore, 70C | 01 fixed 1 m cable with open end |
| 385480-36 | 2500 | Ø12 mm through bore, 70C | 03S12 with a 1 m factory cable |
The 2048-line -40 and -42 variants share their signal format. The -42 needs clearance behind the encoder and its blind bore must match shaft insertion. The -48 fits the -40 shaft geometry but changes position scaling. Treat these as distinct configurations.
Production and end-of-life status
The manufacturer catalogue records were accessible on 8 November 2026. Exact-ID production, orderability and last-time-buy status require manufacturer confirmation. HEIDENHAIN 385480-40 product record.
Specifications
| Parameter | Value and scope |
|---|---|
| Measuring principle | Incremental with integral bearings, differential analog 1 Vpp. 2048 sinusoidal periods per revolution. |
| Supply at encoder | 5.0 V DC ±0.5 V. ERN 480 family current ≤120 mA without load. |
| Signal amplitude | 0.8–1.2 Vpp for A/B under the family catalogue measurement conditions. |
| Reference signal | One reference mark per turn for ERN 480. |
| Cutoff | 180 kHz at −3 dB for this ID. Check actual signal level and receiver limits at operating speed. |
| Rotor and stator fit | Ø12 mm hollow through shaft, 70C. Type 14 coupling on Ø63 mm bolt circle. |
| Operating environment | −40 °C to +100 °C and IP64 per the exact-ID record. |
Use the exact-ID data for ordering. The family catalogue details shaft speed conditions, including the separate two-clamp through-shaft case. At 2048 periods per turn, 6000 rpm gives 204.8 kHz at A/B. Check both the mechanical limit and the feedback electronics. Exact-ID data · Rotary Encoders 349529-2R, ERN 400 drawings and data (PDF).
Mounting and fit
The shaft clamp makes the encoder rotor turn with the machine shaft. The flexible stator coupling holds the housing to the stationary motor or machine face. Check the shaft shoulder, mating diameter, shaft insertion, coupling screw pattern and plug clearance against the applicable drawing. The -40 through bore and the -42 blind bore require different shaft and outlet space.
For the ERN 400 family, the Ø63 mm bolt circle locates the stator fasteners. The manufacturer drawing shows the mating shaft options and clamp position. With the machine isolated, look for fretting, clamp slip, shaft play and contact marks. Use the type 14 sheet for assembly and tightening values. Family dimensions (PDF) · ERN 480 type 14 mounting sheet 387442-93 (PDF).
Interface and measuring method
The ERN 480 produces analog differential A and B voltages about a quarter cycle apart. The receiver uses their phase order for direction and interpolates between cycles for finer position. Count A/B periods to check the line count. The separate R pair signals the reference mark and lets the control establish a machine reference according to its homing logic. After a power cycle the drive needs its reference procedure to re-establish position. Use a receiver or converter specified for 1 Vpp analog feedback. 1 Vpp interface and waveforms (PDF).
Verified wiring
Use this HEIDENHAIN 1 Vpp M23 contact map for the 27S12 socket on IDs 385480-40, 385480-42 and 385480-48. These are numbered contacts at the connector mating interface. Locate them by the molded numbers or the matching connector drawing. Confirm pin view and keying before wiring from the rear. For factory-lead IDs, use the supplied cable drawing for colors and end termination.
| Contacts | Function |
|---|---|
| 12 / 10 | +5 V supply / 0 V return |
| 2 / 11 | Positive / return sense. The corresponding sense and supply conductors join inside the encoder. Wire per the receiver documentation. |
| 5 / 6 | A+ / A− |
| 8 / 1 | B+ / B− |
| 3 / 4 | R+ / R− reference mark |
| 7 / 9 | Vacant for this 1 Vpp layout |
| Shell | Shield termination per the installation drawing. |
The numbers above are for the encoder. Match the machine side to the drive schematic and keep each signal pair together. 1 Vpp pin-layout table (PDF) · Exact drawing D294999 (PDF).
Cables inside the motor and at the machine
The reference build -40 has an external M23 flange socket. HEIDENHAIN lists the following 12-pin M23 cable families. Confirm contact gender, length suffix, receiver pinout, shielding and routing for the application.
| Ordering code | Ends and use |
|---|---|
| 298401-xx | Female M23 connector to male coupling, for extension. |
| 309777-xx | Female M23 connector to stripped ends, for a matched machine termination. |
| 310196-xx | Female M23 connector to male 15-pin D-sub, documented for PWM 20/EIB 74x. Verify the instrument before using it as a bench cable. |
The -02 uses a 1 m factory lead and -36 uses the 03S12 cable configuration. Obtain the cable-end drawing for the exact ID before replacing either. A motor-specific internal loom requires the OEM motor order code and connector documentation. M23 cable and connector catalogue (PDF).
Fault checks
- Inspect externally. Record the alarm, nameplate ID, and whether it follows speed or cable movement. Look for a loose plug, pulled strain relief, damage or contamination.
- Isolate before opening or unplugging. Follow site lockout. Secure the load, isolate drive, motor and separate feedback supplies, wait for discharge and verify absence of voltage. Qualified personnel should inspect pins, shaft retention and stator attachment.
- Check the detached cable. Disconnect both ends. In resistance mode, record probe resistance, check conductors end to end and gently flex near strain reliefs. Check unrelated pairs and signal-to-shell for shorts where the drawing calls for isolation. Account for shield bonds and any intentional links. Keep insulation testers away from connected electronics.
- Check supply and signals under approved conditions. A qualified technician can fit an approved breakout with power isolated, secure motion, then check DC voltage between documented supply and return under load. For the listed 27S12 IDs, check pins 12 and 10 against 4.5–5.5 V at the encoder. Compare receiver and encoder readings where practical. To measure A/B/R, use a suitable differential setup and documented termination.
| Observation | What to check next |
|---|---|
| Supply correct at receiver, low at encoder | Check connector resistance, supply/return continuity and sense wiring. |
| Signals drop when the lead moves | Check the plug, strain relief and harness first. |
| A/B good but homing fails | Check the R path, drive homing settings and mechanical reference. |
| Good feedback at encoder, bad at drive | Check cable, shield, receiver termination and drive configuration. |
| Signals stable but position slips under load | Inspect shaft and stator retention, then drive direction and scaling. |
Motor and drive applications
Identify the receiver’s supported input, line count, supply and reference settings from the drive or controller manual. A documented example of downstream 1 Vpp electronics is the HEIDENHAIN IBV 101, ID 536398-01. It interpolates 1 Vpp into TTL and has its own input-frequency limit. Confirm the actual installation before applying converter limits or selecting a replacement. HEIDENHAIN IBV 101 exact record.
Angle of alignment and commissioning
The documented ERN 480 feedback is A/B plus one R mark. Align the shaft and housing to the mating drawing, then verify direction, count scaling and the machine reference using the OEM commissioning procedure. Save applicable drive parameters before replacement. A motor’s electrical commutation reference comes from its motor/drive design. Obtain that procedure if the work affects it. The ERN 480 family documents give no motor-specific commutation angle or encoder memory restore procedure.
Drawings, pin maps and manuals
- HEIDENHAIN Rotary Encoders 349529-2R, 11/2024 (PDF) · ERN 400 drawings and specifications from p. 38, 1 Vpp and pin layouts from p. 78, M23 cables from p. 88.
- Type 14 mounting instructions 387442-93 (PDF) · Assembly and clamp procedure.
- ERN 400 mating dimensions 374271-12-b-01 (PDF) · Mating geometry.
- D294999 connector pin layout (PDF) · Exact connector assignment drawing.
- Manufacturer product record 385480-40 · Exact-ID data and download index. The three dedicated downloads above currently redirect to the HEIDENHAIN maintenance notice. Request them by document number if needed.
- PWM 21 with ATS (PDF) · Documented 1 Vpp test input.