Site visit or send-in evaluation
Share the complete HEIDENHAIN ID, line count, drive or counter model, supply reading under load and the speed or motion when the fault appears. Include a photo of the flange, shaft and cable termination. Use the enquiry form to share the details.
What specialist testing can show
A compatible differential counter or isolated bench setup can compare A/B direction, line count, reference mark and supply behavior. A differential scope can show missing complements, noise or reduced signal margin at both ends of the cable. Mitchell covers generic incremental feedback. Confirm a supported ROD cable and exact signal and supply before using its tester. This external machine encoder has no documented TI-3000JX motor run configuration in this guide. HEIDENHAIN TTL interface and electrical information (PDF) · Mitchell generic incremental test theory
HEIDENHAIN ROD 426 376846-78 TTL Encoder technical reference
Find your part number
Read ROD 426, the complete ID including suffix and the line count. The examples share the 73A shaft, 01C flange and D294999 connection layout. The line count changes even where the mounting dimensions are the same. Confirm the receiver counts per turn and the factory lead length before substitution.
| ID | Line count and supply | Mechanical and lead configuration |
|---|---|---|
| 376846-78 | 1000 lines, TTL, 5 V ±10% | 73A / 01C, Ø6 × 9.5 mm shaft. 1 m free end. |
| 376846-34 | 250 lines, TTL, 5 V ±10% | 73A / 01C, Ø6 × 9.5 mm shaft. 1 m free end. |
| 376846-P2 | 4096 lines, TTL, 5 V ±10% | 73A / 01C, Ø6 × 9.5 mm shaft. 5 m free end. |
376846-78 record · 376846-34 record · 376846-P2 record
Production and end-of-life status
HEIDENHAIN lists the ROD 400 family and the exact 376846-78 catalogue record. The catalogue establishes the configuration. Confirm current manufacture, exchange or successor options for the exact ID with HEIDENHAIN. Exact 376846-78 catalogue · ROD 400 family
Specifications
| Parameter | Exact configuration |
|---|---|
| Measurement | Incremental TTL, 1000 signal periods per revolution. A controller using four edges per period reads 4000 counts per revolution. |
| Supply and scanning | 5 V DC ±10% at the encoder. Maximum scanning frequency 300 kHz in the exact record. |
| Shaft and flange | Solid Ø6 × 9.5 mm shaft (73A). Ø58 mm synchro flange, Ø50 mm centering collar, three M4 holes on Ø42 mm circle (01C). |
| Cable | 1 m factory cable, free end, suitable outlet for axial and radial routing. Pin configuration D294999. |
| Environment | IP64, −40 to +100 °C as specified by HEIDENHAIN for this ID. |
HEIDENHAIN exact ID and mechanical information · ROD 426 family and TTL data (PDF)
Mounting and fit
The encoder has its own bearings and mounts by its synchro flange. The machine shaft drives the small solid shaft through a separate coupling. Align the two shaft axes and allow the coupling its specified working clearance. Check collar fit, insertion length and fastening dimensions before tightening. Bearing noise or intermittent counts after fitting can indicate shaft preload from an unsuitable coupling or bracket. Use the exact 73A01C mounting document and the coupling instructions for fastener torque. Exact-ID mating and mounting download titles · ROD 426 dimensions and coupling guidance (PDF)
Interface and measuring method
The incremental interface supplies two differential square-wave tracks in quadrature and a reference track. The controller determines movement and direction from A/B order and establishes a reference when it sees the expected index. At 3000 rpm, ID 376846-78 produces 1000 × 3000 ÷ 60 = 50 kHz per A/B track. Check the controller's input bandwidth, count mode and maximum machine speed separately. A 4096-line unit changes the count and track rate in the same mechanics. HEIDENHAIN TTL and reference-track descriptions (PDF) · 1000-line exact ID
Verified wiring
The exact catalogue identifies a free cable end and drawing D294999. The exact drawing download redirected to the manufacturer's maintenance page when checked. Confirm the free-end wire assignment from HEIDENHAIN or the OEM loom drawing before making or energizing a connection.
| Group | Function in the HEIDENHAIN TTL documentation |
|---|---|
| UP and 0 V | Encoder power and return. Verify the exact power conductors before a voltage check. |
| Sensor UP and sensor 0 V | Sense conductors where fitted. Terminate only as shown by the approved encoder and receiver drawings. |
| Ua1 / inverse Ua1 | Track A differential pair. |
| Ua2 / inverse Ua2 | Track B differential pair. |
| Ua0 / inverse Ua0 | Reference pulse pair. |
| Shield | Use the machine shield and connector bonding scheme. |
The HEIDENHAIN catalogue has separate tables for connector families and other outputs. Verify every free-end conductor against D294999 and any OEM splice. 376846-78 Pin Layout listing · TTL wiring functions and connector variants (PDF)
Cables inside the motor and at the machine
The 376846-78 factory lead is 1 m and ends in loose conductors. There is no separate inside-motor PCB loom in this external mounting. The 376846-P2 is a 5 m factory example with 4096 lines. Match the receiving connector and use the machine drawing for extension, shielding and any sense conductors. Confirm the full encoder ID when buying a new factory lead or assembly. 1 m lead configuration · 5 m variant record
Fault checks
Isolate drive, feedback supply and stored mechanical energy before touching the shaft or cable. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
- Visual and mechanical. Check mounting face and screws, coupling clamp and end play, connector condition, shield and strain relief. Inspect for dirt and damage before fitting the plug.
- Detached harness. With the harness isolated from the encoder and receiver at both ends, use resistance mode. First short the meter probes to establish lead resistance. Check each conductor end to end and flex the cable gently at the strain relief. Check between unrelated wires and from signal wires to shield or shell. Expect open only where the drawing calls for isolation. Compare any intentional sense links or shield bonds with the equipment drawing. Keep insulation testers away from connected electronics. Match the reference pair and any sense conductors with the documented cable layout.
- Supply check. A qualified technician can fit an approved breakout while isolated, secure motion and measure documented UP to 0 V with the encoder connected under the site's energized test procedure. Compare at the receiver and the encoder to find a voltage drop. The multimeter measures supply health. Use appropriate differential equipment for the tracks.
- Localize missed counts. Check 1000 lines and x1/x2/x4 scaling. Compare tracks and index at the encoder and at the receiver under safe controlled movement. A good electrical count with wrong machine travel calls for checking coupling and scale. Failures at speed call for checking frequency, signal integrity and receiver configuration.
Motor and drive applications
Use as an external coupled incremental encoder on compatible machine axes, shafts and speed/position inputs. Check exact line count and differential TTL receiver and supply. ROD 436 and ROD 486 family members have different interface options, so physical similarity alone cannot establish compatibility. ROD family comparison (PDF)
Angle of alignment and commissioning
For an external ROD 426, align the coupling and confirm direction, count scale and the machine datum or index approach. Record any indexed relationship before loosening the shaft. With the machine safely recommissioned, verify reference and commanded travel. A separate motor commutation setting applies only where the motor and drive OEM specify it. Incremental reference and direction diagrams (PDF)
Drawings, pin maps and manuals
- HEIDENHAIN 376846-78 exact product. Record for D294999 pin layout, mating dimensions and the 73A01C mounting document. Exact downloadable layout was unavailable during review.
- HEIDENHAIN Rotary Encoders ID349529 (PDF). ROD 426 family dimensions, coupling and differential TTL information.
- HEIDENHAIN 376846-34 exact product. 250-line reference build.
- HEIDENHAIN 376846-P2 exact product. 4096-line, 5 m example.