Site visit or bench evaluation
For a site visit, note whether the fault starts at power-up, during motion or only when nearby equipment switches. For bench evaluation, share the full encoder label, motor order code, drive model and firmware, exact fault and photos of both feedback connectors. If alignment is in question, keep the encoder on the motor so the as-found position can be recorded.
What specialist testing can show
Mitchell lists AD36-0019 and AD36-1219 under BiSS test and alignment support for the TI-5000JX. With the matching BiSS setup, a technician can check whether absolute position and direction track shaft movement, isolate the motor harness with a verified test lead, and measure commutation alignment on the assembled motor. Confirm the Athena profile, firmware and motor connector before connecting. Mitchell test and alignment support
Mitchell also lists both profiles under TI-3000JX Generic BiSS run-test support. A guarded run requires the matched feedback and power leads, amplifier setup, verified motor pole count and established commutation. Check the feedback first. Mitchell TI-3000JX run-test profiles
Hengstler ACURO AD36 technical reference
Read the whole AD36 label
AD36/1219AF.0CBEB, item 0541374, is the digital BiSS-C variant used as the reference here. 1219 gives 12 turn bits and 19 angle bits, A is the 5 V supply code, F.0C is the 8 mm through-bore with F spring tether, BE is digital BiSS-C and the final B specifies the tangential 0.5 m lead. Match the shaft, supply, protocol and cable exit to the original label before ordering.
| Match code and item number | Shaft and termination | Feedback at 5 V nominal |
|---|---|---|
| AD36/1219AF.0CBEB 0541374 |
8 mm through-bore, tangential 0.5 m lead | BiSS-C, 19-bit single-turn + 12-bit multiturn. Digital BE output. |
| AD36/1219AF.0RBV0 0541339 |
8 mm blind hub, 12-pole PCB connection | BiSS-C, 19 + 12 bits, plus 2,048 periods/rev of 1 Vpp sine/cosine (BV). |
| AD36/0019AF.0CBV0 0545067 |
8 mm through-bore, 12-pole PCB connection | BiSS-C, 19-bit single-turn, plus 2,048 periods/rev of 1 Vpp sine/cosine (BV). |
| AD36/0019AF.0CSC0 0541270 |
8 mm through-bore, 12-pole PCB connection | SSI Gray, 19-bit single-turn, with 1 Vpp sine/cosine (SC). |
The family also includes BiSS-B (BI/BC) and 7–30 V (E) versions. A similar label or connector can hide a different interface or supply requirement. Hengstler order key (PDF, p. 6)
Production and end-of-life status
Hengstler’s catalogue lists 0541374 as available to buy, checked 7 November 2026. Confirm availability and lifecycle for a motor-maker-specific suffix with the motor OEM. Hengstler 0541374 catalogue record
Specifications for AD36/1219AF.0CBEB
| Parameter | Value for this variant |
|---|---|
| Measuring method | Optical absolute angle, with a mechanical gear train for the multiturn position |
| Position resolution | 19 bits (524,288 positions/rev) and 12 turn bits (4,096 distinguishable turns) |
| Accuracy | ±35 arcseconds typical. This is separate from the resolution. |
| Encoder supply and load | 5 V DC, −5%/+10% (4.75–5.50 V at the encoder). 150 mA typical without load. Verify polarity before applying power. |
| Electrical interface | BiSS-C binary. Differential RS-422 clock and data. BE lead carries digital feedback. |
| Envelope and fit | Ø37.5 mm housing, Ø8 mm through-bore, F spring tether, IP40 housing and shaft entry |
| Mating shaft motion | ±0.5 mm axial endplay and ±0.05 mm radial runout, hollow or hub designs per Hengstler |
| Encoder speed | 10,000 rpm continuous, 12,000 rpm short term. Check the motor’s own speed limit. |
| Operating temperature | −40 to +120 °C |
How the AD36 fits the motor
The F.0C through-bore fits over the motor’s encoder shaft. Hengstler’s assembly example uses a retaining washer and nut on the exposed shaft. The F spring plate attaches to the motor end face and keeps the housing from turning while allowing the designed flex. Check for a loose shaft retainer, loose tether screws, a bent spring plate or a cable pulling on the housing. Use the motor drawing for the actual retainer and tightening values.
The F.0R blind hub uses a different attachment. Hengstler’s installation drawing B shows a central M4 screw and 2 N·m for that illustrated screw. The through-bore assembly has its own hardware. Compare the motor’s shaft projection, pilot and tether location against the corresponding drawing before fitting. Installation 2 541 033, assembly A/B (PDF) · AD36 hub and through-bore drawings (PDF, pp. 3–4)
How BiSS-C exchanges position with the drive
Clock goes from drive to encoder. Data comes back from encoder to drive.
The drive initiates each reading on CLOCK+/−. The encoder returns a timed digital reply on DATA+/−. A compatible drive can read absolute position while the shaft is stationary.
For 0541374, the reply carries 31 position bits (12 turn + 19 angle), encoder warning and error information, and a 6-bit cyclic redundancy check (CRC). The CRC checks whether the received bits are consistent. A clean frame can still describe a shaft fitted at the wrong mechanical zero. The mechanical turn counter gives this variant absolute multiturn position without a backup battery. The machine reference and motor commutation offset are separate settings.
BiSS-C protocol, point-to-point link (PDF) · Renesas BiSS-C example with AD36/1219AF.0CBEB (PDF)
Verified encoder-side pinout
Use the encoder receptacle mating face in Hengstler’s drawing, with row b above row a and contacts 1–6 from left to right as drawn. The plug’s mating face mirrors this view. Older Hengstler wire colours differ. Verify the actual pin numbers and lead before making a connection.
| Function | AD36 pin | Hengstler current colours | AKD X10, digital BiSS-C |
|---|---|---|---|
| +5 V supply | 1b | White | 10 |
| 0 V return | 4b | Brown | 11 |
| Clock + | 2b | Yellow | 2 |
| Clock − | 5a | Green | 3 |
| Data + | 6b | Pink | 6 |
| Data − | 1a | Grey | 7 |
This table cross-references the six signals. For a complete harness, verify the motor bulkhead drawing, the shield bond and the drive’s approved sense wiring. AKD X10 has separate sense pins 4 and 5. The six-wire BE lead has no dedicated sense conductors. For a BV or SC lead, use the full 12-pole Hengstler diagram for the additional analog and sense wires.
Hengstler receptacle view and old/new colours (PDF, §7) · Kollmorgen AKD X10 pin assignment
Internal motor leads and cable part numbers
| Application | Order number | Length or purpose |
|---|---|---|
| Six-wire lead for BE digital BiSS-C | E1 541 152 | 0.5 m, for cable clip |
| Longer six-wire BE leads | E1 541 186 / E1 541 138 | 1.5 m / 3.0 m, for cable clip |
| 12-wire lead for BV BiSS-C plus 1 Vpp | E1 541 048 / E1 541 117 | Both 0.5 m. First for clip, second for screen clamp plus clip. |
| Cable exit and shield hardware | E2 541 039 / E2 541 034 / 1 541 066 | Axial clip / tangential clip / screen clamp, respectively |
The listed leads end in open conductors. For a motor bulkhead such as M23, verify the OEM connector insert, pinout, shield termination and strain relief separately. Preserve the OEM shield path. Hengstler’s cable clip is a cable exit, so anchor the lead separately near the encoder. Hengstler cable and accessory order numbers (PDF, p. 7)
For Beckhoff AL2000, AM3000 or AM3500 installations with the documented 17-pole motor connection and BiSS plus sine/cosine feedback, Beckhoff lists the external ZK4510-0000-xxxx cable for fixed installation and ZK4510-0020-xxxx for high-flex service. The drive end is a 15-pole D-sub. Match the complete motor code to the drawing. Beckhoff cable drawings and connector views
Fault checks on the machine
Start isolated. Record drive faults and configuration. Lock out all supplies, secure the axis and load, and verify DC bus discharge according to the drive manual. With the harness disconnected from both the drive and encoder, inspect for backed-out pins, dirt, fluid, corrosion and a damaged latch. Meter each conductor end to end, then check for unintended shorts between conductors and to the shell or shield. Gently flex the isolated cable at its strain reliefs. Compare shield continuity with the wiring drawing and keep an insulation tester off the electronics.
Check voltage under load. A qualified technician can fit an approved breakout while isolated and then use the drive’s approved feedback diagnostic state with motion prevented. Set the meter to DC volts, leads in V and COM. For the 5 V A variant, use red at 1b and black at 4b. Expect 4.75–5.50 V at the encoder. Compare the drive and encoder readings if the voltage drops. This check establishes supply health. Use a BiSS-C master or approved differential probing for the serial signals.
Follow the clock, then the reply
| Observation with the axis secured | Next check |
|---|---|
| No clock at the encoder | Check the drive’s feedback mode and port. Clock present at the drive but absent at the encoder points to the outgoing pair or a connector. |
| Clock and supply reach the encoder, but no reply returns | Check clock polarity, the return pair and contact seating. Compare at both ends with a verified harness or bench master before condemning the encoder. |
| Reply arrives, but the drive reports communication errors | Compare configured bit count with the label. Then check supply under load, cable routing, pair integrity and shield termination. AKD F405 is a BiSS watchdog fault. |
| CRC passes, but a warning or error bit is set | The drive received the frame. Read the encoder’s status with the matched diagnostic tool and check the conditions in the encoder manual. |
| Valid position, but the motor starts roughly after feedback work | Check shaft retention, feedback direction, motor phase order and commutation offset before another run. If motor position is correct and the machine still slips, inspect the mechanical load path. |
Kollmorgen AKD fault list · Hengstler ACURO BiSS-C technical manual (PDF)
Motor and drive applications
Kollmorgen documents the AD36-1219 digital profile on the original AKD. In its setup note, the values are FB1.SELECT = 34, FB1.BISSBITS = 31 and FB1.ENCRES = 1048576. The AD36-0019 profile uses 19 bits and an ENCRES value of 4294967295 in the same note. Use these as comparison values for that drive and supported profile with the axis disabled. Check the drive revision and preserve the existing parameter set before changes. Kollmorgen AKD BiSS-C settings
On a Kollmorgen AKM2, AKM3 or AKM4, older cable documentation lists AD36 with AA (single-turn) or AB (multiturn) as BiSS-B. Read the actual encoder suffix before using this BiSS-C wiring or profile. For a Beckhoff AX5000, Beckhoff distinguishes pure digital BiSS-C on the AX572x card at X41/X42 from BiSS-C plus analog sine/cosine at X11/X21. Confirm the drive, card, firmware and motor option together. Kollmorgen motor feedback options (PDF) · Beckhoff AX5000 encoder interface
Commutation alignment and motor memory
Record as-found commutation and export the original drive settings before disturbing a readable assembly. The correct offset depends on the motor, phase order, feedback direction and installed position. On AKD applications using a configured drive offset, MOTOR.PHASE sets the offset in electrical degrees. Use the exact motor’s approved commissioning method to verify it after fitting. Any phase-finding test that can move the shaft belongs on a secured setup under a qualified technician’s control.
Hengstler identifies OEM memory in BiSS-C banks 4–7 and reserves banks 0–3 for configuration and manufacturer data. If the motor OEM requires a memory transfer, read and save the original with the documented profile, restore only approved OEM data to a verified matching part and read it back. Verify alignment and machine reference separately. A fixed bench lockup angle and an OEM memory map for the specific motor installation must come from that motor’s documentation. Hengstler BiSS-C bank map (PDF) · AKD MOTOR.PHASE reference
Drawings, manuals and training notes
- Hengstler AD36 data sheet, 081123 EN (PDF). Specs and pins on pp. 1–2, shaft drawings on pp. 3–5, order key and cables on pp. 6–7.
- Hengstler AD36 installation instructions 2 541 033 (PDF). Assembly drawings and connector orientation.
- Hengstler ACURO BiSS-C technical manual 2 547 133 (PDF). Status and register details.
- Kollmorgen AKD installation manual Rev. AB, §9.12.8.2 (PDF). X10 digital BiSS-C wiring example.
- Mitchell BiSS serial protocol. Mode B, Mode C and options with analog sine/cosine.
Ask SpareFaber about on-site diagnosis, alignment or bench testing