Identify the fitted part
| Guide scope | Hengstler AD36 SSI — Standalone device |
|---|---|
| Feedback identity | AD36 SSI |
| Main designation | AD36 SSI |
| Documented motor example | No complete fitted motor order has been verified; retain every nameplate suffix. |
| Interface | SSI absolute, order-specific |
| Starting connection | Match the fitted connector and OEM drawing; exact lead assignment remains open |
| Configuration distinction | GTY2 covers AD36 BiSS-C; the SSI branch has a different electrical setup and order code. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | TI-5000JX feedback evaluation is conditional on the exact fitted option and verified fixture. Read the SSI interface code, singleturn/multiturn resolution, shaft option and connector orientation. |
|---|---|
| Starting lead / fixture | Match the fitted connector and OEM drawing; exact lead assignment remains open |
| Profile / module | Verify exact supply, profile, connector and installed software. Named model evidence does not establish a complete fitted setup. |
| TI-3000JX motor-run scope | Motor-run setup conditional on exact motor, feedback, poles, wiring, alignment, lead/module and installed TI-3000JX profile. |
The documented test reference is Hengstler Encoders — AD36 SSI. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current order availability and a verified successor for the exact fitted item remain to confirm. Technical documentation does not establish stock or a drop-in replacement. Match mechanical fit, interface, connector, memory and motor/drive requirements before ordering.
Specifications and interface
| Interface / feedback option | SSI absolute, order-specific |
|---|---|
| Order-dependent fields | SSI Gray/binary, position word length, turn field, supply and optional analogue signals must be decoded from the full order. |
| Connector drawing | Use the correct 12-pole PCB contact view and axial/radial orientation. Do not borrow AD58 wire colours. |
| Exact dimensions and fastening | Use the matching manufacturer outline, shaft drawing and revision. No universal shaft torque, air gap or fastener setting is assigned. |
SSI uses separate clock and data paths. Decode the exact Gray/binary format, position bits, turn field and timing from the order documentation. Where TTL or sine/cosine tracks are present, inspect them independently from the serial position. A plausible number from guessed word framing is not proof of a healthy matched installation.
Mechanical fit and retention
Photograph the incoming reference, locating seat, shaft restraint, fasteners and cable exit before removal. Inspect accessible looseness, contamination, rubbing and bearing condition after isolation. Use the fitted outline for shaft engagement, retention and rear clearance. Preserve the incoming alignment and do not force an encoder or apply a torque from a similar-looking assembly.
AD36 is a family with SSI and BiSS variants. The linked technical datasheet identifies SSI Gray and binary options and separate optional sine/cosine outputs. Match the complete order rather than assigning the headline 22-bit capability to every SSI unit. Hub-shaft and through-hollow-shaft drawings, supply options and 12-pole connector orientation must be read together.
Wiring and connector boundaries
Treat the sensor plug, internal motor loom, bulkhead, external machine cable and receiver as separate interfaces. Confirm contact numbering, keying, gender and the drawing view before tracing conductors. Identify supply/return, signal pairs, temperature, shield and any separate brake wiring individually. Obtain the contact diagram for the actual connector before wiring an adapter. The linked datasheet supplies connector drawings; preserve the selected SSI option and drawing revision. Do not mix AD36 and AD58 contact numbering or wire-colour columns.
Starting connection for this guide: Match the fitted connector and OEM drawing; exact lead assignment remains open. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
An exact internal OEM loom part number has not been established for the fitted unit. Record both loom ends and obtain the motor assembly drawing. External cable choice depends on receiver, length, shielding and fixed/flexing installation. A Mitchell test lead identifies a bench connection, not an OEM machine-cable replacement.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the configuration first | AD36 is a family with SSI and BiSS variants. The linked technical datasheet identifies SSI Gray and binary options and separate optional sine/cosine outputs. Match the complete order rather than assigning the headline 22-bit capability to every SSI unit. Hub-shaft and through-hollow-shaft drawings, supply options and 12-pole connector orientation must be read together. |
|---|---|
| Intermittent fault while the cable moves | After isolation and disconnection at both ends, inspect flex points, repairs, pin engagement and contamination. Compare continuity and unintended shorts against the exact drawing, allowing for intentional shield bonds. |
| No signal or communication | Verify full order, interface, fixture and supply range. A qualified technician can compare source and load voltages with the approved breakout and OEM procedure; connector shape alone does not specify supply. |
| Position reads but the drive still rejects feedback | Check the independent signal paths, direction, motor identity and any supported reference/turn status. Record the original alarm before changing settings. A data reset is not a substitute for identifying the fault. |
Alignment, reference and memory
Record the incoming shaft datum, direction, motor phase convention and recoverable data before disturbing feedback. Use the exact OEM procedure and supported equipment for alignment or replacement. Matching electrical signals alone does not establish the correct motor pairing or machine origin.
Motor and drive applications
AD36 SSI fitted application to verify. GTY2 covers AD36 BiSS-C; the SSI branch has a different electrical setup and order code.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Hengstler Encoders — AD36 SSI
- Hengstler AD36 BiSS/SSI datasheet 081123 EN — Exact family, feedback option, connection drawing and revision only
- Hengstler ACURO AD36 family — SSI/BiSS family; match exact interface, shaft, resolution and connector code.
Obtain the complete fitted order, internal loom drawing, connector contact view and approved fixture before fitted-unit work. The linked family document does not establish interchangeability for every order.
Common questions
What should accompany a AD36 SSI enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Motor-run setup conditional on exact motor, feedback, poles, wiring, alignment, lead/module and installed TI-3000JX profile. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.