Site visit or send-in evaluation
We check the fine position track, coarse rotor angle signals and reference pulse before recommending harness or encoder work. Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Mitchell documents Siemens S21-family checks with the TI-5101 module and TI-5010 motor lead or TI-5090 direct lead. Match the exact .005 wiring first. Qualified bench checks compare A/B, R and C/D separately. Verify TI-3000JX motor run support, phase wiring and software selection for the exact motor before any run.
Hengstler S21-2048.005 0548005 1 Vpp Sin/Cos Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is S21-2048.005. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| S21-2048.005 / 0548005 | Ø58 mm housing, 1:10 taper on the exact Hengstler datasheet. | 2,048 periods of A/B, one period of C/D and one reference pulse per turn. 14 PCB positions in rows a and b. |
| 0548001 / 0548002 / 0548003 / 0548004 | Earlier S21 builds cited in the .005 datasheet. Check dimensions and cable arrangement. | Retain the actual motor-side connection drawing and check commutation for the installed motor. |
Production and end-of-life status
Hengstler's exact-item page offers 0548005. Confirm lead time and any production or supersession statement directly with Hengstler for this order number.
Specifications
| Parameter | Value and scope |
|---|---|
| Supply | 5 V DC ±10%. Up to 120 mA without load per the .005 datasheet. |
| A/B | 2,048 periods per revolution, differential 1 Vpp sin/cos |
| C/D | One period per revolution, differential 1 Vpp sin/cos commutation |
| R track | One reference pulse per turn, amplitude greater than 0.4 V in the datasheet |
| Frequency response | 500 kHz −3 dB limiting frequency |
| Fit and enclosure | Ø58 mm housing, 1:10 taper, IP40 for housing and shaft input |
| Operating temperature | −15 °C to +120 °C |
The table identifies the assembly each value applies to. Main technical PDF.
Mounting and fit
Use the motor shaft and encoder taper drawings as a pair. The taper centres the encoder rotor, and the stator mounting stops the housing from following the shaft. Check seating, the applicable centre fastener and housing restraint with the assembly isolated. An apparent fit can still leave an axial gap or strain the flexure.
Compare the installed cable clearance and witness marks before refitting. Use the motor's stated fastener, tightening and alignment procedure.
Interface and measuring method
The receiver interpolates the phase of the A/B sine and cosine pair for fine position. The R pulse establishes a repeatable reference when the axis passes it. C/D give a coarse angle over one mechanical turn for commutation. A drive can show motion with good A/B while refusing to enable because C/D are shifted or absent.
Verified wiring
These are the encoder PCB cavity numbers from page 2 of the Hengstler .005 datasheet. Identify rows a and b from the keyed PCB header and drawing. The motor bulkhead and mating cable require their own view.
| Function | Cavities |
|---|---|
| Supply / return | 1b UB / 5b GND |
| Supply sense / return sense | 7a / 3a |
| A+ / A− | 6b / 2a |
| B+ / B− | 3b / 5a |
| R+ / R− | 4b / 4a |
| C+ / C− | 7b / 1a |
| D+ / D− | 2b / 6a |
Verify supply at the encoder supply and return under the specified load, using the OEM's approved sense wiring. Trace the pairs with the loom disconnected before making any powered connection.
Cables inside the motor and at the machine
The .005 uses a two-row PCB header. On Siemens motor assemblies, confirm the exact PCB-to-bulkhead loom number from the full motor MLFB and connector label. Mitchell lists TI-5010 for the documented Siemens motor side and TI-5090 as a direct lead. Check the socket and polarity rather than using the same 14-cavity numbering at the bulkhead.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Axis moves on feedback but drive fails at enable | Check C/D amplitude and commutation relation with the exact Siemens motor procedure. |
| Fine counts drift or jump | Check the A/B pair and loaded supply. Trace intermittent faults at the harness and motor connector before opening the encoder. |
| Homing misses the reference | Verify the R pulse at the receiver, direction and the OEM homing configuration. |
| Cyclic noise follows a refit | Check seating, rotor clearance and stator flexure before changing signal thresholds. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Mitchell describes S21 feedback on applicable Siemens motors. Confirm the MLFB and fitted label before using a Siemens drawing for 0548005. Compare the Mitchell ERN 1387 and S21 comparison for a related signal principle and its separate mechanical and connector variants.
Angle of alignment and commissioning
Record the original C/D angle against the motor phase reference before moving the encoder. The 1 Vpp and one-period specifications describe the feedback, while the correct commutation offset comes from the motor configuration. Use the documented Siemens model procedure and verify direction, R index and commutation after fitting.
Drawings, pin maps and manuals
- Main technical PDF. Hengstler S21-2048.005 technical datasheet, version 1 10082020HF, manufacturer document hosted by a distributor. Page 2 has the PCB pin and signal table.
- Manufacturer reference. Match the exact order code or the identified motor option.
- Mitchell Siemens 1 Vpp feedback guide. Identifies bench lead options and distinguishes the fine and commutation tracks.