Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
A CANopen master and known-good matching cordset can help confirm heartbeat, object access, PDO operation and position versus shaft movement. Verify a dedicated Mitchell CANopen profile before selecting that tester. Machine movement and motor running require their own documented setup.
ifm RM9001 CANopen Absolute Multiturn Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is RM9001. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| RM9001 | 10 mm solid shaft and synchro flange. Match the pilot and coupling dimensions. | 24-bit CANopen absolute position, 12 bits per turn and 12 bits of turn count. |
| RMS0024-C24UST | The longer type marking for the same ifm RM9001 in the manufacturer sheet. | Same referenced electrical build. Treat it as a label alias for RM9001. |
Production and end-of-life status
ifm lists RM9001 under type RMS0024-C24UST and issued revision RM9001-01 on 23 May 2025. Confirm current orderability and support with ifm.
Specifications
| Parameter | Value and scope |
|---|---|
| Position | 4,096 positions per turn and 4,096 turns, binary, with supported scaling and preset. |
| Supply | 9–30 V DC. ifm specifies a Class 2 source for the cULus installation. |
| Current | Less than 100 mA at 10 V DC and up to 50 mA at 24 V DC as listed on RM9001-01. |
| Mechanical | 10 mm solid shaft and synchro flange. Drawing shows M4 tapped mounting holes with 6 mm depth. |
| Bus defaults | 125 kbit/s, node ID 32 on the RM9001-01 data sheet. Read the installed settings before assuming defaults. |
| Connection | One five-contact M12 A-coded connector on the encoder. See page 3 for the numbered assignment. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Use the synchro flange and shaft drawing together. Seat the pilot square, allow the flexible coupling's specified engagement and travel, and match its bore to the 10 mm shaft. Check clearance at the encoder face and the cable exit. Shaft side load can make the position erratic even while the CANopen link is healthy.
When replacing a unit, record coupling position, actual mounting clamp or screws and machine datum. Use the fastener and coupling limits from the installed assembly instructions.
Interface and measuring method
The encoder places its absolute turn and shaft position on a CANopen bus. The controller needs the correct node ID, bit rate, object mapping and operating state. A node that answers an SDO may still fail to produce the expected PDO. Compare heartbeat and status before treating a stationary process value as failed feedback.
Verified wiring
RM9001-01 page 3 gives these device pin numbers for the M12 A-coded connector. Match the drawing and connector mating side. The sheet labels CAN reference and power return separately.
| Pin | ifm designation |
|---|---|
| 1 | CAN_GND |
| 2 | VBBc, encoder supply |
| 3 | GND (PE), as designated on the data sheet |
| 4 | CAN_H |
| 5 | CAN_L |
Follow the machine CANopen diagram for bonding, screen, branch length and termination. Measure the network's isolated termination only with the affected segment in its documented state.
Cables inside the motor and at the machine
Use an A-coded five-contact cordset wired for CANopen with the specified twisted pair, shield and connector gender. The motor PCB-to-M23 loom does not form part of this external encoder. Confirm machine cable length and the trunk or spur drawing before selecting an order code.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| No CANopen response | Check the documented supply under load, the reference conductor, CAN_H and CAN_L continuity and bus rate. |
| Duplicate ID or intermittent network | Read the current address, inspect termination and branches, then isolate the encoder with a known-good test segment. |
| Frames valid but position differs | Verify scaling, preset, direction and mapping. Inspect the isolated coupling for slip. |
| Communication stops when machine moves | Inspect strain relief and cable carrier, and compare errors against motion and load. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
A PLC, motion controller or machine position system can use RM9001 when its CANopen interface and position model match. Treat it as a separate external encoder. The controller project defines how its preset, direction and rollover relate to machine travel.
Angle of alignment and commissioning
Archive the current node settings and machine position before replacement. Establish the same mechanical datum and read back the preset and direction using the controller's commissioning procedure. Verify position and rollover over permitted travel. Motor commutation alignment applies only to a documented motor installation.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- RM9001-01 connector assignment. Manufacturer-authored English data sheet on a distributor mirror.