Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
A qualified technician can verify stored parameters and observe A/B/Z through a controlled turn using the configured supply and receiver. Compare at both ends of the harness. Confirm any exact Mitchell profile and harness before use.
ifm RUP500 Programmable HTL/TTL Incremental Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is RUP500. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| RUP500 | Solid Ø6 mm shaft and synchro flange. Display and 8-pin A-coded M12. | Programmable magnetic incremental encoder. Factory settings 1,024 P/R and HTL. |
| RUP500, IO-Link connection | Same product and connector. Use the correct mode-specific cable. | C/Q on pin 4. The connection diagram differs from encoder pulse mode. |
| RUP500, speed monitor or preset counter | Same product with a distinct selected application. | Output functions follow the selected mode. Use the diagram for that mode. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Supply | 4.75–30 V DC per data sheet. Match the active output mode and receiving input requirements. |
| Resolution / output | 1–10,000 programmable. Factory 1,024 and HTL. A/B phase difference 90° in encoder mode. |
| Speed / frequency | Data sheet specifies maximum electrical speed 12,000 rpm and switching frequency 1,000 kHz. Check the combined limit with the selected resolution and mode. |
| Fit | Solid 6 mm shaft, synchro flange, A-coded 8-pin M12. |
| Data / protection | IO-Link for parameterisation and diagnostics. IP65 assembly rating with housing and shaft ratings listed separately. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Read the mounting drawing for shaft projection, flange registration and the M4 threaded depth. Check mating coupling, shaft alignment and panel clearance for the display. The connector can be used in radial or axial orientation as shown in the drawing.
Interface and measuring method
The magnetic incremental encoder supplies A/B and index pulses in its encoder mode. The control counts them to follow direction and speed. HTL and TTL are selectable output types, so read the installed parameter before connecting a receiver. An IO-Link master accesses the separate IO-Link connection for configuration and diagnostics.
Verified wiring
The datasheet has separate diagrams for encoder, IO-Link, speed monitor and preset counter. Use the numbered 8-pin A-coded M12 view for the configured mode.
| Pin | Signal |
|---|---|
| 1 / 3 | UB / GND |
| 2 / 6 | A / A− |
| 5 / 7 | B / B− |
| 4 / 8 | Z / Z− |
| Plug screen | Follow the drawing |
For the IO-Link connection, pin 1 is L+, pin 3 is L− and pin 4 is C/Q. Leave the other contacts unused as marked. In the encoder diagram pin 4 carries the index. Verify the mode before connecting either circuit.
Cables inside the motor and at the machine
Use the ifm exact product's Accessories and Connection pages to choose the A-coded female 8-pin lead. Verify its screen, the far-end receiver or master and the intended mode. The datasheet states up to 100 m in the wired application and a separate 20 m IO-Link maximum. Check the full application conditions.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Supply present, counter stays at zero | Read the selected operating mode, HTL/TTL setting and pin assignment. Compare with the receiving input. |
| Count ratio wrong | Check programmed resolution and receiver edge counting. Compare actual shaft motion against the pulse count. |
| IO-Link master cannot see the device | Check the correct port mode, IODD, supply and C/Q wiring using the IO-Link diagram. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use on industrial rotary machines with a compatible incremental input, speed monitor or IO-Link master. Verify mechanical fit, cable and parameter storage in the existing controller.
Angle of alignment and commissioning
Save or record the mode, resolution, output type, direction and application settings before replacement. Set the coupling and verify count direction and the machine datum. If the machine has servo commutation alignment, handle it under the motor and drive procedure.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Mode-specific connection diagrams. Encoder, IO-Link and speed-monitor pins.
- ifm instructions and IODD. Select the exact product downloads and accessories.