Identify the fitted part
| Guide scope | Intek MPM Hall feedback — Motor application |
|---|---|
| Feedback identity | Record the fitted feedback maker and complete designation; the named motor family is not a sensor part number. |
| Manufacturer MPN / full suffix | MPM Hall feedback is the scoped family/designation. Match every additional character on the fitted label before ordering. |
| OEM service ID / motor order | Not established for a specific fitted unit. Record the full motor label, feedback option and any OEM service ID separately. |
| Interface | Hall commutation |
| Documented starting connection | TI-5718, 18-contact bayonet, shared Hall/motor-power connection |
| Material distinction | TCG388 Custom Servo MPM incremental and TCG362 MTS MPM resolver are different manufacturers and interfaces. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Check the documented position channels and separately identified index/commutation/tach paths. Exact output level, pin map and fixture must be verified. |
|---|---|
| Starting lead / fixture | TI-5718, 18-contact bayonet, shared Hall/motor-power connection |
| Profile / module | Exact supply, output level, channel set and any amplifier to verify. |
| TI-3000JX motor-run scope | No complete motor-run approval established by this proposal. Verify motor poles, power/brake wiring, alignment, fixture and the installed TI-3000JX profile. |
The admission evidence is Mitchell Test Cable Index by Manufacturer Support — PDF page 7, TI-5718 row. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current production status, exact-order stock and an approved successor have not been confirmed in the cited evidence. Retain the installed label and ask for an exact-order check before selecting a replacement.
Specifications and interface
| Verified technical boundary | Separate Hall feedback from motor power on the combined connection before planning a test. |
|---|---|
| Supply / output compatibility | Use the complete fitted label and its wiring drawing. No universal supply, receiver level or excitation is assigned to this family guide. |
| Exact dimensions, torque and pins | Use the scoped drawing or request it through the enquiry. Values from another suffix, connector view or motor revision are not substituted. |
The documented feedback is Hall commutation. Check its states, transitions and receiving requirements under the fitted motor procedure. The index does not establish quadrature A/B/Z, pulse resolution or a tachometer.
Mechanical fit and retention
Photograph the incoming shaft/coupling position, locating seat, restraint, fasteners and cable exit before removal. Check accessible looseness, contamination, bearing roughness and signs of rubbing after isolation. Identify whether the assembly has its own bearings, a hollow-shaft clamp or a motor-retained sensor; the exact drawing controls that decision. Do not lever against a sensing disc or apply a torque from a similar-looking model.
The Intek MPM index describes Hall feedback and motor power sharing an 18-contact bayonet connection. Identify those contact groups before any fixture is energized. Hall states provide commutation information; no A/B pulse resolution or tachometer is established by this row.
Wiring and connector boundaries
Map five boundaries separately: the sensor plug or PCB, internal motor loom, motor bulkhead, external machine cable and drive/tester end. Record connector gender, keying, contact numbering and whether the drawing shows mating or termination side. The documented Mitchell lead is a starting fixture, not a pin map for a handmade adapter. Keep power, temperature, brake, shield and feedback contacts identified individually.
Starting connection for this guide: TI-5718, 18-contact bayonet, shared Hall/motor-power connection. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
No internal OEM harness number or universal extension has been verified for this exact fitted order. Obtain the motor assembly drawing and photograph both loom ends before sourcing it. A fixed installation cable and a cable-carrier extension may have different flex and shielding requirements. Do not convert the Mitchell test-lead number into an OEM replacement part number.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Hall states appear plausible but the motor does not start | Verify the phase relationship and common supply/return using the actual drawing; state changes alone do not establish correct commutation. |
|---|---|
| Combined bayonet connector was repaired | Identify and verify motor-power contacts separately from Hall contacts under isolation. Obtain the complete contact map before any powered fixture is used. |
Alignment, reference and memory
Record the incoming Hall sequence and relationship to motor phases before disturbing the assembly. Use the exact motor-specific phase convention and approved fixture. No generic Hall replacement angle or memory transfer is established here.
Motor and drive applications
MPM Hall feedback. TCG388 Custom Servo MPM incremental and TCG362 MTS MPM resolver are different manufacturers and interfaces.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Mitchell Test Cable Index by Manufacturer Support — PDF page 7, TI-5718 row
- Generic Incremental Quadrature Pulse Encoders — Named article section, model or attached table. See each proposal row for the exact scope and locator.
Exact OEM technical PDF remains to obtain. The Mitchell reference establishes only the documented device or motor/feedback connection; it does not fill missing ratings or pins.
Common questions
What should accompany a MPM Hall feedback enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
No complete motor-run approval established by this proposal. Verify motor poles, power/brake wiring, alignment, fixture and the installed TI-3000JX profile. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.