What specialist testing can show
TI-5000JX bench. Confirm within-turn and turn data, the exact fitted EKM36 and any scoped memory access.
TI-3000JX motor run. Confirm the full AKM order and supported DSL motor-run configuration.
Starting lead. Match the AKM connection code and approved HIPERFACE DSL lead or direct fixture.
Kollmorgen / SICK AKM GF / EKM36 Multiturn HIPERFACE DSL Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| AKM GF / EKM36 | Optical multiturn HIPERFACE DSL. Match the fitted frame and motor connection code. |
| AKM GE / EKS36 | Optical singleturn HIPERFACE DSL. Compare how the application retains turns. |
| AKM GB / SKM36 | Multiturn conventional HIPERFACE with separate analogue feedback tracks. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Position format | 18 bits per turn and 12 turn bits (4,096 turns) for GF in the Kollmorgen connectivity guide. |
| Feedback supply | 7–12 V DC in the AKM GF selection table. The approved integrated connection depends on the fitted order. |
| Drive scope | Kollmorgen’s GF connectivity row identifies AKD/S700 options. Verify exact drive, firmware and connection. |
Interface and measuring method
HIPERFACE DSL carries digital feedback on a matched link. Inspect feedback alarms, data stability and valid turn information. The conventional HIPERFACE analogue test applies to a different interface.
Mounting and fit
Check the fitted EKM36 order and AKM motor drawing for rear mounting and rotor attachment. Preserve the original orientation and the route of the feedback wires through the hybrid connection where used.
Wiring and connector scope
Use the Kollmorgen connection map for the full order. Identify the DSL feedback pair and its routing through the machine connector. Verify the direct EKM36 connector separately.
Internal motor and machine cables
Match the motor and drive orders to the OEM connectivity document. If the machine cable is hybrid, check the feedback pair and screening as a separate circuit from the motor power and brake.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Turns change unexpectedly after replacement | Confirm the GF EKM36, drive mode and original reference. |
| Fault appears when the hybrid cable moves | Inspect the feedback pair, connector keying and strain relief. |
| Drive sees a device but flags mismatch | Compare GE/GF code and the original motor data. |
Angle of alignment and commissioning
Record the original position, direction and motor memory where supported. Confirm the fitted DSL software and commissioning reference before replacing the feedback or enabling the motor.
Motor and drive applications
Kollmorgen AKM with verified GF option and matched connector
Read GF and preserve the multiturn data and OEM reference before choosing an encoder or cable.
Drawings, pin maps and manuals
- Kollmorgen AKM support. Mitchell-linked AKM Feedback Description, GF row and supported DSL family
- Kollmorgen AKM connectivity manual, GF EKM36 option. Supplementary reference for the stated model or setup.
- Mitchell-linked AKM Feedback Description. Reference for the fitted feedback or motor option.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.