Site visit or send-in evaluation
Send the complete MiniCODER code and wheel drawing or label, the CNC/drive model, the fault speed or angle and photos of the installed head and cable termination. Where the fault follows one wheel position, mark that position before removing parts. Use the enquiry form to share the details.
What specialist testing can show
A qualified specialist can check the differential tracks and reference pulse over one turn with a matched wheel, approved receiver or suitable differential instrumentation. Lenord+Bauer lists its GEL 211CS service unit for the MiniCODER. The basic bench signal test needs the matching tooth geometry and gap. Exact Mitchell TI-5000JX or TI-3000JX use with this head and wheel was not verified. Lenord+Bauer service device and technical information · D-51T-2449 function test and assignments (PDF copy)
Lenord+Bauer MiniCODER GEL 2449 Spindle Encoder technical reference
Find your part number
Record the complete GEL 2449 type and the wheel data separately. In the manufacturer type code, K is the 1 Vpp signal pattern, Z the tooth reference, P the parameterizable option, L the left tangential outlet, 1 or 4 the target-wheel module code and the following letter the cable termination. The three digits specify lead length. A final dash marks no temperature lead. The rows are ordering examples from the type-code fields. Match your own label.
| Ordering example | Wheel and nominal gap | Cable build |
|---|---|---|
| 2449 KZPL1K030- | Module 1.0. 0.50 ± 0.02 mm nominal gap. | Type K flying lead, 0.3 m |
| 2449 KZPL4K050- | Module 0.4. 0.20 ± 0.01 mm nominal gap. | Type K flying lead, 0.5 m |
| 2449 KZPL4J050- | Module 0.4. 0.20 ± 0.01 mm nominal gap. | Type J 12-pin male, 0.5 m |
| GEL 2449 connection M or N | Confirm module 1 or 4 on the same label. | Angled (M) or straight (N) 17-pin M23 panel socket. Some have a separate temperature lead. |
D-51T-2449 ordering fields and cable drawings (PDF copy)
Production and end-of-life status
Lenord+Bauer currently documents GEL 2449 and publishes revision D-51T-2449. Confirm orderability of the full head code and any OEM target-wheel drawing with Lenord+Bauer. Manufacturer product record
Specifications
| Parameter | Manufacturer data |
|---|---|
| Sensing | Bearingless magnetic scan of a ferromagnetic steel target wheel, with a tooth reference mark. |
| Electrical | 5 V DC ±5%, ≤50 mA without load, two differential sinusoidal tracks in quadrature at nominal 1 Vpp and a rectangular reference signal. |
| Frequency | 0–200 kHz. The wheel, tooth count, mounting and spindle requirements also limit speed. |
| Target wheel | Module 1.0 or 0.4 and width ≥8.6 mm in the manufacturer technical table. Use the wheel drawing for exact teeth, bore and reference geometry. |
| Lead and head | Catalogued cable Ø5 mm, minimum bend radius 25 mm for the basic design. IP68 applies at the MiniCODER housing cable outlet. |
| Working temperature | 0 to +70 °C in the working range. Check the different storage/operating limits and connector ratings on the data sheet. |
Lenord+Bauer technical data · Mechanical and electrical technical tables (PDF copy)
Mounting and fit
The head mounts on the stationary housing and the steel wheel runs with the spindle. Use the hole pattern, tooth-centre geometry and air-gap table in the technical information. Check gap at multiple wheel positions under the OEM procedure. This helps separate a fixed setup error from eccentricity or a damaged tooth. Match the head to the wheel module and tooth reference. Confirm wheel balance, fit, maximum speed and allowable runout with the spindle and wheel drawings before a run test. MiniCODER hole pattern, gap table and setting method (PDF copy) · Precision target-wheel drawings (PDF)
Interface and measuring method
The head scans each tooth into one period of the sine and cosine tracks. The downstream interpolator uses both tracks to resolve position within a tooth period. A separate tooth feature supplies the reference. For a wheel with N teeth at speed r rpm, the track frequency is N × r ÷ 60 Hz. Check both the input bandwidth and the specific wheel's allowed speed. A good speed reading can coexist with a missing reference, which matters during spindle orientation and tool changes. Signal tracks and reference diagram (PDF copy) · Reference-tooth selection (PDF)
Verified wiring
The assignments below compare the K flying lead and the M/N 17-pin panel socket with no temperature sensor lead. For J, P, U or Z, open the separate diagram. Identify the connector view from the drawing before making a lead.
| Function | Type K colour / test connector pin | Type M or N panel socket pin |
|---|---|---|
| +5 V supply | Red / 1 | 10 |
| 0 V | Blue / 9 | 7 and 15 (bridge per drawing) |
| Track 1 + / − | White / 2 and brown / 3 | 1 / 2 |
| Track 2 + / − | Pink / 4 and black / 5 | 11 / 12 |
| Reference + / − | Gray / 7 and yellow / 8 | 3 / 13 |
| 5 V sense | Green / 6 | 16 |
The shield is separate from the 0 V signal. Use the manufacturer's connector instructions and the machine screening scheme. Preserve the test connector when needed for the manufacturer service tool. Temperature-cable builds use additional pins shown in the M/N temperature table. Connection types, plug-in views and shield rules (PDF copy)
Cables inside the motor and at the machine
The type-code termination and length select the factory MiniCODER lead. K is the flying lead supplied with a factory test connector. M and N are M23 panel sockets that can carry a separate temperature cable. Use the matching assembly on the control side and verify shielding and remote sense with its diagram. Lenord+Bauer lists head lead lengths by termination. Confirm the OEM extension and wheel data separately before placing an order. Cable and ordering tables (PDF copy)
Fault checks
Isolate and secure the spindle before checking fit. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
- Inspect. Check head fasteners, mounting face and connector, tooth damage, metallic debris and cable strain. Record the gap and condition at several angular positions before moving the head.
- Isolated interconnect. With the harness isolated from the encoder and receiver at both ends, use resistance mode. First short the meter probes to establish lead resistance. Check each conductor end to end and flex the cable gently at the strain relief. Check between unrelated wires and from signal wires to shield or shell. Expect open only where the drawing calls for isolation. Compare any intentional sense links or shield bonds with the equipment drawing. Keep insulation testers away from connected electronics. Preserve polarity of the track pairs and keep screen and signal return separate according to the diagram.
- Check supply and signals. Only under the approved energized procedure, a qualified technician can use a correctly wired breakout fitted while isolated. Measure the 5 V supply at the head under load. Use differential measurement for each signal pair and compare the head and CNC ends. Respect guarding and speed limits.
- Separate patterns. A dropout that repeats once per revolution points toward a wheel/gap condition. An error that follows the cable movement calls for checking contacts and conductors. Clean sine/cosine but absent index calls for checking the reference tooth, its gap and reference pair before replacing the head.
Motor and drive applications
The GEL 2449 is a position and speed readhead for a compatible CNC or spindle drive with the appropriate differential analog input. The wheel, machine index and signal conditioning are part of the installation. Match the module, reference mark and receiver. Manufacturer spindle application overview · MiniCODER family and interface comparison (PDF)
Angle of alignment and commissioning
Set the head geometry and validate the wheel reference and CNC spindle orientation using the spindle OEM procedure. Record the original gap, wheel position and orientation offset before removal. If the wheel or head position changes, recheck the reference pulse and the tool-change position before returning the machine to service. Spindle orientation and any separate motor commutation procedure use their own references. Air-gap adjustment and functional check (PDF copy) · Tooth-reference position and applications (PDF)
Drawings, pin maps and manuals
- Lenord+Bauer D-51T-2449 download. Manufacturer download for exact connector drawings, type code, installation and service checks.
- D-51T-2449 technical information (PDF copy). Manufacturer-authored copy covering all documented termination variants.
- Lenord+Bauer precision target wheels (PDF). Wheel/reference combinations, dimensional definitions and speed considerations.
- Lenord+Bauer GEL 2449 product page. Current manual links, technical data and manufacturer service device.