What specialist testing can show
TI-5000JX bench. For a fitted and identified resolver, use the resolver input with an approved connection. Compare winding continuity and angle tracking on the matched excitation.
TI-3000JX motor run. Confirm the exact BS23 motor order, power connection and verified run configuration before a powered test.
Starting lead. Select a resolver fixture after confirming the fitted BS23 termination, excitation and ratio.
MOOG BS23 Brushless Motor Resolver Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| BS23 / BS23HP | Silencer brushless motor family, documented by Mitchell and MOOG. Capture the suffix and serial number. |
| BS23 with resolver option | Use a motor drawing or machine wiring plan that shows resolver excitation and two return circuits. |
| FASTACT G/G4xx | Separate MOOG family. Mitchell places the TI-5920 and TI-3032 cable references under this family. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback method | Passive AC excitation and angular sine/cosine returns for the resolver option. |
| Example motor dimensions | MOOG’s BS23HP family table gives a 2.6 in housing diameter and 1.91–2.91 in length range. These are motor envelope figures. |
| Fitted resolver ratings | Obtain excitation frequency, voltage, transformation ratio and terminal map from the motor order drawing. |
Interface and measuring method
A resolver has a reference winding and returns whose relative amplitudes carry shaft angle. Isolated winding continuity is a first check. A matched excitation and signal measurement is needed to compare amplitude, phase and tracking.
Mounting and fit
Use the fitted BS23 rear assembly drawing before disturbing the resolver. Record shaft reference, stator location and the route of the feedback conductors. Inspect the strain relief from outside the assembly first.
Wiring and connector scope
Trace excitation, sine and cosine circuits from the fitted motor and drive drawings. Keep the reference pairs separate from motor phases and any Hall connections. TI-5920 and TI-3032 refer to the FASTACT drawing in the Mitchell article.
Internal motor and machine cables
Compare the as-built harness to the machine schematic before a continuity check. Record both termination styles, shield bond and the motor order if the original drawing is missing.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
A resolver is passive. Check isolated winding continuity against the matching drawing. Use the specified AC excitation on the approved test fixture for a signal check.
| Symptom | What to verify |
|---|---|
| Angle reading absent | Check the resolver option and trace the reference winding and excitation path. |
| Angle weak or unstable in part of a turn | Compare both returns and isolate any intermittent cable section. |
| Stable angle with a commutation alarm | Verify the resolver direction, phase reference and drive setting. |
Angle of alignment and commissioning
Preserve the incoming motor electrical reference and resolver direction. Confirm the phase and return convention against the exact drive before specialist alignment. A scope or resolver tester can help separate an alignment shift from an open winding.
Motor and drive applications
BS23 brushless DC motor with the documented resolver option
Identify the fitted BS23 resolver option and separate return, cable and drive reference faults.
Related SpareFaber guides
Drawings, pin maps and manuals
- MOOG Motors. BS23 brushless DC motor section. The separate FASTACT G/G4xx section contains the resolver wiring example and TI-5920/TI-3032.
- MOOG brushless motor catalogue, BS23 section. Supplementary reference for the stated model or setup.
- MOOG BS23 high-performance motor. Confirms resolver as a factory option. The exact fitted termination and resolver ratings require the order drawing.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.