Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Check A/B and marker at each documented interface with compatible instrumentation. When one path reads normally, diagnose the other at its connector and again at the receiver. Account for shared power or wiring before treating both paths as independent.
Nidec Avtron AV685N1E8Y8YC000 Dual-Output Incremental Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is AV685N1E8Y8YC000. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| AV685N1E8Y8YC000 | N standard temperature, 1 threaded rod tether, E end-shaft mount. | Two 8Y high-power HX modules at 1024 ppr each. C is the MS plug and conduit adapter option. 000 adds no modification. |
| AV685 mounting option T | Through-shaft housing configuration. Check its drawing and clearance. | Select output modules and connector independently. |
| AV685 line driver option 9 | Mount selected separately. | Fixed 5 V output option. Check receiver thresholds before replacing an option 8 module. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Mount | End-shaft AV685, nominal 1⅛ in hollow shaft per model page, 12 in threaded tether B32809. |
| Output selection | Left and right 8Y, each 1024 ppr. Manufacturer selection table gives option 8 as 5–24 V in and 5–24 V out. |
| Connection | Option C is a 10-contact MS-style connection with mating plug and flex conduit adapter. |
| Environment | Temperature option N is −20 to +80 °C. Enclosure series rating IP66 subject to the specified assembly. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
The hollow bore sits over the machine shaft. The tether prevents the housing from following the shaft. Match the end-shaft hardware and tether travel to the installation manual. An incorrectly anchored tether can load the housing as the shaft moves axially. Check for loose clamps and unsupported conduits while isolated.
Interface and measuring method
Two magnetic incremental modules report movement independently. The receivers determine direction and speed from A/B phase and use the marker if configured. Treat each module as its own path through its supply, connector, cable and receiver. Compare the two counts over the same approved motion before attributing a mismatch to the shaft.
Verified wiring
| Function group | Contacts in the Avtron option-C wiring figure |
|---|---|
| Power common / supply | A / B |
| Phase A pair | D and G |
| Phase B pair | E and H |
| Marker pair | C and I |
| Alarm reference / output | F / J, use the approved alarm circuit |
Use the manual's differential wiring figure for true and complementary orientation, and inspect the key and contact letters before mating. Read the correct figure for each installed module. Use the manufacturer's grounding guidance and avoid linking the two supplies or commons without the machine schematic.
Cables inside the motor and at the machine
Option C includes the mating MS plug and flex conduit adapter. Verify the connector build and wiring on both sides. The manufacturer publishes distinct MS and alternative pinout options. Order a compatible plug or harness by the complete option and application drawing.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| Only one receiver drops out | Compare its local supply, module status, MS contacts and receiver input with the working path. |
| Both lose counts together | Check common shaft fit, tether, runout and the shared machine supply or routing. |
| Encoder shows an alarm | Capture LED and alarm state and inspect the mechanical and electrical conditions in the manual. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use on drives with a compatible heavy-duty hollow-shaft mount and separately verified receiving inputs. The exact code is corroborated by a supplier listing and decoded against Avtron's manufacturer selection table.
Angle of alignment and commissioning
Use the installation drawing for shaft engagement and tether alignment. Retain receiver count, direction and marker settings, then verify both paths after refitting.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- Manufacturer installation and wiring manual. Use the option-C MS differential drawing and alarm wiring diagrams.
- Product page and current selection table. Check which mechanical, driver and connector options are fitted.
- Exact code corroboration. Supplier listing establishes the configured code. Use the manufacturer selection table for the electrical rating.