Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
Use OMRON drive diagnostics to check encoder communication and local position. Check an isolated, disconnected harness against the cable drawing. Confirm exact motor and interface support before using a generic encoder test instrument.
OMRON 1S R88M-1M40030T-BS2 Absolute Servo Feedback technical reference
Find your part number
Use the full label and suffix. The main reference is R88M-1M40030T-BS2. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| R88M-1M40030T-BS2 | 400 W motor, 3000 rpm rated, with holding brake. | OMRON absolute feedback. Identify the matched 1S drive and CN2 loom. |
| R88M-1M40030S-S2 | Separate 1S motor order. Check the suffix and dimensional table. | Compare the documented motor and cable combination. |
| R88D-1SN04H-ECT | 200 V class 400 W drive in the 1S manual. | EtherCAT controller link is separate from CN2 motor feedback. |
Production and end-of-life status
The listed technical records identify this model. Confirm current production and orderability for the exact suffix with the manufacturer when sourcing a replacement.
Specifications
| Parameter | Value and scope |
|---|---|
| Identification | The primary MPN is the complete motor order. Confirm the internal encoder assembly by motor serial. |
| Motor | OMRON lists 400 W, 230 V AC motor class, 3000 rpm and holding brake. |
| Feedback and drive | Absolute motor encoder. 1S documentation describes battery-free multiturn feedback for the series. |
| Cable | Motor feedback is connected to CN2 on the specified drive. Select the 400 W motor cable table in I586. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
Use the brake-equipped 400 W outline to check flange, motor length, shaft and connector clearances. Secure the mechanical load independently before disconnecting power or the brake. Inspect the separate feedback connector and its cable support. Use the OEM service instructions before opening the feedback assembly.
Interface and measuring method
The drive reads absolute position from the motor encoder over the dedicated feedback connection. EtherCAT links the drive to the control system. If the drive has a valid local position while the controller reports a fault, inspect network and axis mapping separately from the encoder loom.
Verified wiring
Identify drive connector CN2 and the motor-side encoder connector in I586. Check the exact cable and connector view before probing. The 1S manual also shows drive-side pulse outputs and network connections elsewhere. Use the CN2 cable assembly drawing for the motor feedback signals.
Cables inside the motor and at the machine
I586 lists the R88A-CR1A family for the relevant 400 W motor group. Documented standard lengths include R88A-CR1A003C, R88A-CR1A005C and R88A-CR1A010C. Check the motor connector, flex need and cable-length limit. Match brake and power cables separately.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| EtherCAT healthy, encoder communication fault at drive | Check the exact CN2 loom, motor plug, supply path and terminal condition. |
| Drive position valid, PLC position missing | Check drive status, mapped process values and EtherCAT project. |
| Mechanical axis drifts or jams | Secure the load and inspect brake, coupling, motor and axis. Compare feedback position with observed movement through the approved procedure. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use the I586 compatibility table and motor label to confirm the actual 1S drive and connection. Record both part numbers, drive alarm and any recent cable, brake or motor changes.
Angle of alignment and commissioning
Read the drive and axis reference parameters before motor removal. An internal encoder replacement requires the OEM service and alignment procedure. After reinstallation, verify the machine reference and approved brake and motion checks.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- I586 1S user manual. Use the compatible drive and motor tables, CN2 section and R88A-CR1A cable drawings.
- I821 1S product catalogue. Motor outline and cable options by power and motor class.
- 1S family overview. Battery-free multiturn description and system scope.