What specialist testing can show
TI-5000JX bench. Check position and commutation through the documented test path with the power and brake circuits identified.
TI-3000JX motor run. Confirm the full motor order, power lead, phase reference and supported TI-3000JX setup.
Starting lead. TI-5736 for the documented 23-contact bayonet.
ORMEC MAC-G ABZ/UVW Hybrid Servo Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| MAC-G with 23-contact bayonet | Documented TI-5736 branch for ABZ/UVW, power and brake. |
| MAC-G feedback order | Check the encoder and drive type in the ORMEC manual. Confirm the actual count option. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Position | The OEM overview gives 8,000 counts per revolution after fourfold quadrature decoding for its standard reference. Verify the ordered option. |
| Commutation | Separate UVW feedback on the Mitchell connection. |
| Connector | 23-contact bayonet with separate feedback, power and brake circuits. |
Interface and measuring method
Incremental edges give motion and direction. Confirm raw encoder lines and controller-decoded counts as separate figures. UVW commutation and brake behavior each have their own diagnostic path.
Mounting and fit
Use the MAC-G frame drawing and rear feedback assembly details. Preserve motor reference, encoder orientation and the cable’s route through the combined shell.
Wiring and connector scope
Identify the approved feedback section of the 23-contact view. Keep motor phases and brake isolated during disconnected feedback checks. Use the OEM diagram for the exact order.
Internal motor and machine cables
Record the full hybrid cable and both connector views. Check pin engagement, locking, shield and strain relief before dismantling the motor.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Motion scale differs by a factor of four | Compare the raw line count with the controller’s quadrature count. |
| Position present but drive fails to enable | Check UVW and brake and phase setup separately. |
| Intermittent response at the bayonet | Inspect the contact and verify isolated conductor continuity. |
Angle of alignment and commissioning
Capture the original count direction, index and commutation relation. Use the motor’s ORMEC setup and phase convention after any feedback replacement.
Motor and drive applications
ORMEC MAC-G with 23-contact feedback/power/brake bayonet
Find the exact MAC-G order and isolate the feedback portion of the shared motor connector.
Drawings, pin maps and manuals
- Mitchell Test Cable Index by Manufacturer Support. Ormec Support Part Numbers, TI-5736
- ORMEC ServoWire SAC-SW hardware manual, MAC-G motor chapter. Supplementary reference for the stated model or setup.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.