What specialist testing can show
TI-5000JX bench. TI-5000JX Sanyo Denki serial profile and a separate Generic Incremental check on the verified breakout.
TI-3000JX motor run. Mitchell describes E07B151306 in its Sanyo motor-run manual. Confirm the actual motor, configured feedback and custom harness first.
Starting lead. Verified custom lead for E07B151306. Match the Table 2.16 reference and actual harness.
Sanyo Denki E07B151306 ABSOSYN Serial and ABZ Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| E07B151306 | Mitchell documents the full suffix with serial absolute position and A/B/Z. It calls out a user-fabricated connection using the matching wire map. |
| E07B151103 | The earlier guide at TCG121 covers this distinct ABSOSYN build. It has A/B and no Z in the cited example. |
| R11G4113A | A separate serial-only branch with a different supply requirement. Match the actual encoder suffix before selecting a fixture. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Serial position | 15 bits, or 32,768 positions per turn, for E07B151306. |
| Turn data | 13-bit turn field, documented by Mitchell as ±4,096 turns. |
| Incremental feedback | A/B/Z with 32,768 decoded counts per revolution in the cited bench setup. |
Interface and measuring method
The drive reads serial angle and turn information, while the separate incremental channels give motion and index feedback. A good serial count can coexist with a bad Z path. Check both before deciding whether the fault is inside the encoder.
Mounting and fit
Read the motor order and full encoder suffix. Record the original rotor or coupling seat, stator restraint and cable exit. Verify mounting dimensions and hardware against the actual motor drawing.
Wiring and connector scope
Mitchell refers to its Table 2.16 wire and terminal assignments for this branch. Confirm the current equivalent reference and actual lead colors before making a breakout. Use the fitted drawing for supply, serial pairs, incremental signals and retention.
Internal motor and machine cables
The supported-types chart calls for a verified custom breakout on this suffix. Identify the OEM motor plug and internal loom separately. Keep the full conductor map for any approved replacement.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Serial position works and index is missing | Confirm the suffix and trace the Z pair, connector and coupling. |
| Both position paths are intermittent | Inspect the common supply, cable strain relief and isolated harness. |
| Turn value changes unexpectedly | Verify the selected encoder profile and retention arrangement before resetting anything. |
Angle of alignment and commissioning
Record the incoming motor reference and retained position, then confirm direction and index behavior on the exact motor setup. Use the matched drive procedure for restoring the machine reference.
Motor and drive applications
Motor and external connector to verify
Obtain actual motor order, current wire map, exact connector and battery instructions.
Drawings, pin maps and manuals
- Sanyo Denki Motors and Serial Encoders. E07B151306 and supported-types table
- Mitchell Sanyo Denki supported-types table. E07B151306 index and custom fixture row.
- Mitchell Sanyo Denki Motors. Run selection and resolution for this suffix.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.