What specialist testing can show
TI-5000JX bench. Match the SSI word, analogue signals and connector to the fitted AG7Y variant.
TI-3000JX motor run. Specific run setup remains open for the fitted DR motor and drive.
Starting lead. Choose the exact AG7Y connector and verified SSI/analogue test connection.
SEW-EURODRIVE AG7Y Multiturn SSI and 1 Vpp Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| AG7Y | Shaft-centered plug-in option in the SEW DR catalogue. |
| AS7Y | Spread-shaft option with a related signal format and different mounting. |
| EG7S | Plug-in incremental version. Verify the controller needs absolute SSI before selecting a replacement. |
Production and end-of-life status
SEW’s predecessor and successor table documents the plug-in shaft and newer cone-shaft families. Verify the complete motor order and mechanical conversion requirements.
Specifications
| Parameter | Verified scope |
|---|---|
| AG7Y supply | 7–30 V DC in the linked SEW technical data. |
| SSI data | Gray code, 4,096 positions within one turn and 4,096 revolutions in the turn field. |
| Analogue tracks | 2,048 sine/cosine periods per revolution and 1 Vpp. SEW also specifies 8,192 increments under its count convention. |
| Connection | Terminal strip in the removable cover on the documented branch. |
Interface and measuring method
The drive clocks the SSI word to read absolute position and turn count. The analogue path carries incremental movement. A good SSI word does not establish the amplitude or continuity of the analogue tracks.
Mounting and fit
The legacy DR catalogue shows a 14 mm motor-side bore with an M6 threaded end for the applicable plug-in frame group. Confirm the installed DR order and exceptions before fitting. Check the torque bracket, seating and cable cover clearance.
Wiring and connector scope
Use the AG7Y terminal-strip drawing. Confirm the supply, differential clock and data pairs and analogue tracks independently. Use the fitted connector view and drive termination.
Internal motor and machine cables
Trace the terminal strip to the drive and record the screened cable, extensions and motion route. Confirm a successor’s connection drawing before reusing the original loom.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| SSI reads correctly but speed feedback is unstable | Check the 1 Vpp tracks, shielding and analogue receiver separately. |
| Position jumps at a full turn | Verify Gray decoding and the configured within-turn and turn fields. |
| Replacement cannot seat | Check plug-in shaft versus spread shaft and compare the motor bore drawing. |
Angle of alignment and commissioning
Record the received absolute position and any mechanical datum before opening the assembly. After fitting, verify SSI direction and turn behavior and compare the incremental tracks against the machine reference.
Motor and drive applications
SEW DR160–225 on the documented AG7Y option
Identify the plug-in shaft and verify cable and mechanical differences before considering a successor.
Related SpareFaber guides
Drawings, pin maps and manuals
- SEW Servo Motors. Mitchell-linked absolute encoder table, AG7Y plug-in shaft row
- SEW plug-in shaft predecessor and cone-shaft successor table. Supplementary reference for the stated model or setup.
- SEW DR motor catalogue. Section 9.5.5 for AG7Y and the shaft-centered mounting table in section 9.6.
- SEW AG7Y technical data. AG7Y column for supply, SSI data, analogue tracks and connection.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.