Identify the fitted part
| Guide scope | SEW-EURODRIVE CMP112H / BY / RH1M — motor feedback application |
|---|---|
| Feedback identity | RH1M; fitted feedback label and connector to verify |
| Model / configuration identifier | CMP112H / BY / RH1M |
| Motor order scope | Documented frame/feedback/brake configuration; not a complete winding, thermal-sensor or connector order |
| Interface | RH1M resolver |
| Starting connection | TI-5908 only at the matching 12-contact M23 resolver connection; confirm excitation, winding pairs and connector view. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | TI-5000JX named CMP resolver evaluation; actual profile, supply, connector and fixture must match the fitted unit. Brake release is a separate controlled circuit; bench feedback support is not brake approval. |
|---|---|
| Starting lead / fixture | TI-5908 only at the matching 12-contact M23 resolver connection; confirm excitation, winding pairs and connector view. |
| Profile / module | Confirm resolver excitation, ratio and phase relationship. RH1M has no serial motor-memory path. |
| TI-3000JX motor-run scope | Conditional on exact TI-3000JX motor/feedback profile, poles, phase order, alignment, power connection, restraint and amplifier envelope. Brake rating, control and release must be confirmed before rotation. No full-rating run capability is inferred from bench support. |
The documented test reference is SEW Servo Motors — Mitchell named CMP resolver family; OEM drawing p.67, brake BY; no extra encoder extension added. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
The linked manufacturer document identifies this catalogue configuration. Current production, availability and any approved successor require confirmation against the complete fitted order. A downloadable manual does not prove present stock. Compare voltage, winding, mounting, shaft, brake, feedback, connector and stored motor-data requirements before accepting a replacement.
Specifications and interface
| Feedback technology | RH1M resolver |
|---|---|
| Frame / feedback / brake configuration | CMP112H / BY / RH1M |
| Motor square flange | 190 mm |
| Motor shaft diameter | 38 mm; see drawing for tolerances |
| Overall axial length, including shaft | 692 mm; with BY brake |
| Brake scope | with BY brake |
| OEM outline reference | Printed page 67 of CMP catalogue 27799468/EN, November 2023 |
| Order scope | Frame, feedback and stated brake; complete winding, thermal-sensor and connector order not established |
| RH1M sensor class | Two-pole resolver; one pole pair |
| Excitation reference | Mitchell table: 7 V AC nominal; verify fitted frequency, transformation ratio and supported setup before applying excitation |
| Motor-memory scope | No serial-encoder motor-memory read or copy operation for this resolver |
| Service values | Exact encoder coupling dimensions, pin map and tightening torque require the fitted assembly drawing. |
RH1M is a resolver, not a serial absolute encoder. Excitation and both analogue winding responses must be assessed together through a full mechanical revolution. A lost winding pair, poor contact, incorrect excitation or an altered phase relationship can each produce incorrect position. The two-pole designation describes the resolver; it does not establish the motor pole count. A resolver does not provide retained multiturn machine position.
Mechanical fit and retention
Record the incoming shaft datum, pilot, bolt circle, rear clearance, cable exit and encoder retention before removal. Inspect play, debris, moisture and damaged contacts. Follow the exact assembly drawing for fits and fasteners; motor flange dimensions do not establish encoder coupling dimensions or tightening torque. Use the CMP112H outline on printed page 67. Its 190 mm flange and 38 mm shaft are independent dimensions. Verify pilot, bolt-circle, shaft projection, rear clearance and cable bend clearance from the same drawing. The CMP112 body envelope is 205 mm, while the square flange is 190 mm. Use the shared feedback outline for the specified brake condition; do not add the 24 mm extension shown for smaller unbraked CMP frames. The brake changes the motor package. Compare the brake outline with the unbraked parent before judging replacement fit.
CMP112H / BY / RH1M identifies a 190 mm square flange, 38 mm shaft and 692 mm overall axial length including the shaft, with BY brake. This is a frame/feedback/brake configuration; winding, speed, thermal-sensor and connector suffixes still require the complete motor nameplate.
Wiring and connector boundaries
Keep motor power, protective earth, feedback and temperature circuits separate. Match contact numbering, keying, gender and mating-face versus wire-side view. Connector appearance alone is insufficient to establish a pin map. TI-5908 only at the matching 12-contact M23 resolver connection; confirm excitation, winding pairs and connector view. Establish reference, sine and cosine winding pairs from the actual connection drawing. Check isolation and continuity with the assembly disconnected and the permitted measurement method. Supply frequency and transformation ratio must match the fitted resolver and selected tester setup. The BY brake is a separate circuit from feedback. Do not infer coil voltage, current, holding torque or release time from the BK/BP/BY family code. Check the fitted brake label and exact OEM circuit, including any control or suppression components. Separate failure to release and mechanical drag from missing or unstable feedback. Never apply brake power through the encoder fixture. Confirm brake release, load restraint and the supported motor setup before specialist rotation. No emergency-stop capability is inferred.
Starting connection for this guide: TI-5908 only at the matching 12-contact M23 resolver connection; confirm excitation, winding pairs and connector view.. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
Record the internal encoder-to-motor loom separately from the external machine cable and bench fixture. The internal loom part number is not established by the frame or interface alone. Obtain both connector faces, the assembly diagram and the correct contact view. Match cable length, shielding, temperature rating and fixed or flexing duty to the installation. A Mitchell test lead identifies a test connection; it is not an OEM replacement machine cable.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Identify the exact configuration | CMP112H / BY / RH1M identifies a 190 mm square flange, 38 mm shaft and 692 mm overall axial length including the shaft, with BY brake. This is a frame/feedback/brake configuration; winding, speed, thermal-sensor and connector suffixes still require the complete motor nameplate. |
|---|---|
| Intermittent fault during cable movement | After isolation and disconnection at both ends, inspect flex points, pin engagement, contamination and earlier repairs. Compare continuity and unintended shorts against the correct diagram, accounting for intentional shield bonds. |
| Unstable position or missing feedback | Verify the actual sensor profile, matched excitation or DC supply, contact view and fixture. Inspect both analogue paths where applicable. A connector that mates mechanically can still have an incompatible pin assignment. |
| Position reads but the drive rejects it | Check the resolver winding relationship, phase convention and exact motor profile. A serial-memory reset is not an RH1M diagnostic. |
| Replacement dimensions look close | Compare this exact flange, shaft, feedback housing, brake and connector arrangement with the linked drawing. Do not use magnet-stack length, family digits or a similar power rating as the complete mounting envelope. |
| Motor will not move or brake drags | The BY brake is a separate circuit from feedback. Do not infer coil voltage, current, holding torque or release time from the BK/BP/BY family code. Check the fitted brake label and exact OEM circuit, including any control or suppression components. Separate failure to release and mechanical drag from missing or unstable feedback. Never apply brake power through the encoder fixture. Confirm brake release, load restraint and the supported motor setup before specialist rotation. No emergency-stop capability is inferred. |
Alignment, reference and memory
Preserve the original mechanical reference, phase convention, rotation direction and readable drive settings before disassembly. Communication or a smooth position reading alone does not prove correct electrical alignment or the machine reference. Use the fitted SEW resolver procedure and exact motor profile. Mitchell describes a common SEW convention of +U/−V at 60 electrical degrees and +U/−W at 120 electrical degrees for most applicable motors; this is not a universal value. Confirm whether the actual motor follows that convention before alignment. RH1M has no serial memory from which to recover a motor-specific offset.
Motor and drive applications
CMP112H; 190 mm square flange; shaft Ø38 mm; brake BY. CMP112H / BY / RH1M identifies a 190 mm square flange, 38 mm shaft and 692 mm overall axial length including the shaft, with BY brake. This is a frame/feedback/brake configuration; winding, speed, thermal-sensor and connector suffixes still require the complete motor nameplate.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- SEW Servo Motors — Mitchell named CMP resolver family; OEM drawing p.67, brake BY; no extra encoder extension added
- SEW Standard Alignment — Named family and feedback option, rechecked 11 November 2026
- SEW-EURODRIVE CMP40–CMP112, 27799468/EN, November 2023 — 27799468/EN, November 2023; exact CMP112H / BY / RH1M drawing, printed page 67. Axial length includes shaft.
- Batch 26 SEW CMP feedback and brake drawing cross-check — 27799468/EN 11/2023 pp.35,37,40,43,44,49,51,57,59,65,67; EK1H/AK1H table and named CMP resolver in Mitchell SEW article. Small-frame BK, medium BP, CMP112 BY. Exact motor order and brake rating remain to inspect.
Obtain complete fitted motor and feedback labels, exact service ID, internal loom and connector mating-face drawing. Confirm the linked document revision, fitted retention and enabled test setup before extending replacement, wiring or motor-run claims. SEW title is a frame/feedback/brake configuration; complete winding, thermal-sensor and connector suffixes remain to record.
Common questions
What should accompany a CMP112H / BY / RH1M enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Conditional on exact TI-3000JX motor/feedback profile, poles, phase order, alignment, power connection, restraint and amplifier envelope. Brake rating, control and release must be confirmed before rotation. No full-rating run capability is inferred from bench support. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.