Identify the fitted part
| Guide scope | Tamagawa TS5645-N110 ABZ/Rx — Standalone device |
|---|---|
| Feedback identity | TS5645-N110 ABZ/Rx |
| MPN / full suffix | TS5645-N110 ABZ/Rx is the scoped designation. Retain all additional order characters and manufacturer IDs. |
| OEM service ID / motor order | Exact fitted-unit service number and motor order are not established; record them separately. |
| Interface | Incremental ABZ / Rx connection |
| Starting connection | TI-5631, named 17-pin MS ABZ/Rx connection |
| Configuration distinction | TCG181 is TS5645N122. N110 has its own named ABZ/Rx connection; complete order and serial functions remain to verify. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Conditional TI-5000JX bench scope: Check the N110 ABZ/Rx wiring and mechanical package; distinguish it from the N122 Meiden serial assembly. Match the fitted drawing and enabled test profile. |
|---|---|
| Starting lead / fixture | TI-5631, named 17-pin MS ABZ/Rx connection |
| Profile / module | Match exact profile, supply, connector and installed software; named cable evidence is not a complete setup. |
| TI-3000JX motor-run scope | Motor-run setup remains conditional: verify exact motor, poles, power/brake wiring, direction, alignment and installed TI-3000JX profile. |
The admission evidence is Mitchell Test Cable Index by Manufacturer, 1 April 2019 — Tamagawa TI-5631 row: TS5645-N110 ABZ/Rx, 17-pin MS. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current exact-order availability and an approved successor have not been confirmed. The linked technical references identify a configuration, not stock or universal replacement compatibility. Compare full labels, mechanics, interface, connector and motor data before ordering.
Specifications and interface
| Verified technical scope | Check the N110 ABZ/Rx wiring and mechanical package; distinguish it from the N122 Meiden serial assembly. |
|---|---|
| Exact fitted order | Full suffix/ID, contact drawing, supply and receiver must match the actual assembly. Family specifications do not establish every unit. |
| Dimensions, fasteners and torque | Use the matching manufacturer drawing and revision. Unverified dimensions, air gap, torque and pin assignments remain open. |
Keep pulse periods, decoded edges and machine scaling separate. Assess direction, reference and any independent commutation/Rx path according to the fitted drawing. TTL, HTL and analogue sin/cos require different receiving and supply arrangements; a matching connector shell does not establish electrical compatibility.
Mechanical fit and retention
Photograph the incoming shaft reference, locating seat, restraint, fasteners and cable exit before removal. After isolation, inspect accessible looseness, contamination, bearing roughness and rubbing. The actual drawing determines whether the unit has integral bearings, a clamped shaft or motor-supported sensing. Do not force a sensing assembly or substitute a torque from a similar model.
The TI-5631 index row explicitly names TS5645-N110 and ABZ/Rx on a 17-contact MS connection. Keep N110 separate from the N122 Meiden serial assembly. Check A/B/Z independently from Rx; the cable row does not establish a decoded Rx protocol, retention arrangement or complete motor-run profile.
Wiring and connector boundaries
Record the sensor plug, internal motor loom, motor bulkhead, external machine cable and drive/tester end as separate interfaces. Confirm gender, keying, contact numbering and mating-versus-termination view. Keep feedback, temperature, brake, motor power and shield contacts identified individually. A named test lead is not a pin map for an unverified adapter.
Starting connection for this guide: TI-5631, named 17-pin MS ABZ/Rx connection. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
No internal OEM loom number or universal extension has been established for the exact fitted unit. Obtain its motor assembly drawing and both loom-end photographs. Select fixed or cable-carrier cable according to the actual installation, shielding and flex requirements. Mitchell lead numbers describe test fixtures and are not OEM replacement harness numbers.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Configuration to establish first | The TI-5631 index row explicitly names TS5645-N110 and ABZ/Rx on a 17-contact MS connection. Keep N110 separate from the N122 Meiden serial assembly. Check A/B/Z independently from Rx; the cable row does not establish a decoded Rx protocol, retention arrangement or complete motor-run profile. |
|---|---|
| Intermittent fault when the cable moves | With power isolated and both cable ends disconnected, inspect flex points, repairs, engagement and contamination. Check continuity and unwanted shorts using the correct contact drawing, allowing for intentional shield bonds. |
| No signal or communication | Confirm the fitted order and approved fixture before a qualified technician measures the specified supply using the OEM procedure. Compare source and load at the appropriate breakout; a connector shell does not specify voltage. |
| Position moves but the drive still rejects feedback | Record identity, position, alarms and direction. Check the supported signal paths, retention and motor pairing separately; do not reset or overwrite data as a first diagnostic step. |
Alignment, reference and memory
Record the incoming mechanical datum, direction and motor phase convention before disturbing feedback. Preserve recoverable identity, offsets and parameters where the exact interface and equipment support reading. There is no universal angle or memory image for this family. A specialist replacement requires the fitted motor procedure, supported fixture and verified hardware/data compatibility. Establish the machine homing/index procedure independently; incremental motion alone does not retain machine origin after power loss.
Motor and drive applications
Standalone feedback; fitted motor and full order to verify. TCG181 is TS5645N122. N110 has its own named ABZ/Rx connection; complete order and serial functions remain to verify.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Mitchell Test Cable Index by Manufacturer, 1 April 2019 — Tamagawa TI-5631 row: TS5645-N110 ABZ/Rx, 17-pin MS
- Tamagawa Serial Encoders — Named model, option or linked technical table
Exact fitted order, internal loom, contact view, fixture, supply and motor-specific setup remain to verify. Exact primary OEM PDF still to obtain.
Common questions
What should accompany a TS5645-N110 ABZ/Rx enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Motor-run setup remains conditional: verify exact motor, poles, power/brake wiring, direction, alignment and installed TI-3000JX profile. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.