What specialist testing can show
TI-5000JX bench. TI-5000JX Tamagawa TS5781N13 serial and separate incremental count checks on the correct 15 V fixture.
TI-3000JX motor run. Confirm the complete motor order, approved fixture and a specific supported run profile for this N13 application.
Starting lead. TI-5667 on the Mitchell OSA130 / TS5781N13 application.
Tamagawa TS5781N13 15 V Serial and ABZ Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| TS5781N13 / OSA130 | Mitchell’s supported-types table lists this label, TI-5667 and the Matsushita / Toshiba application. Read the fitted motor order separately. |
| TS5781 | Family designation. Confirm the N13 suffix and inspect the battery compartment before applying this guide. |
| TS5778 | A separate Tamagawa design covered by the Shinko and Kobelco guides. Its data and index behavior differ. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Serial angle | 12 bits, or 4,096 counts per mechanical turn. Mitchell reports clockwise forward serial count on the N13. |
| Turn data | 14-bit turn field with a documented range of 14,400 turns on this model. |
| Incremental channels | A, B and Z. Mitchell lists 5,000 periods or 20,000 decoded counts per revolution. |
| Supply and interface | 15 V DC encoder supply on N13. The request circuit and the serial output have distinct electrical levels. Use the exact fixture drawing. |
Interface and measuring method
The receiver uses serial angle and a turn field, while the separate A/B/Z channels track movement and provide a reference. Test serial count and incremental count as two independent paths. Confirm the separate request circuit when the serial reply is missing.
Mounting and fit
Photograph the OSA130 and N13 markings, installed shaft coupling and feedback connector. Use the fitted motor and encoder drawing for mounting dimensions and the battery compartment layout.
Wiring and connector scope
Use the TS5781 section and TI-5667 reference to identify supply, return, request, serial output and incremental pairs. Confirm the original retention wiring before disconnecting it. A standard 5 V harness may lack the circuits the N13 requires.
Internal motor and machine cables
TI-5667 is the Mitchell test cable. Find the machine cable and any internal harness by the motor order and both plug views. Keep the battery path and the machine shield termination distinct.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Serial reply missing | Verify the N13 fixture and request path. Compare the isolated harness and supply with the correct drawing. |
| Serial angle is good and motion count is erratic | Check the A and B pairs, index, strain relief and coupling separately. |
| Battery or position-retention alarm | Identify the fitted battery arrangement and preserve the machine reference before following the OEM battery procedure. |
Angle of alignment and commissioning
Record the original shaft reference and retained position before removal. Verify rotation convention, serial count, index and machine reference after fitting with the approved motor procedure.
Motor and drive applications
Matsushita / Toshiba application in Mitchell’s supported-types table
Obtain fitted motor order, exact TI-5667 pin view, internal loom and applicable retention instructions.
Drawings, pin maps and manuals
- Tamagawa Serial Encoders. TS5781 and the supported-types table
- Mitchell Tamagawa supported-types chart. TS5781N13 row and scoped test cable.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.