Site visit or send-in evaluation
Share the full feedback ID, machine or motor order code, drive or controller model and fault history. Send photos of the label, mating connectors and mounting. Tell us if the fault followed a repair, cable change or controller replacement. Request a UAE site visit or bench evaluation.
What specialist testing can show
An approved EtherCAT diagnostic master can help distinguish link and position faults. FSoE validation belongs to the configured safety system and the applicable manual. Check exact Mitchell protocol support independently. Keep any powered bench measurement separate from authorization to run the machine.
TWK TRK58-KPA65536R4096S3MK01 Safety over EtherCAT Encoder technical reference
Find your part number
Use the full label and suffix. The main reference is TRK58-KPA65536R4096S3MK01. The related rows identify distinct configurations or label codes. Match the actual assembly before substituting.
| Exact ID or order code | Mechanical configuration | Electrical or service distinction |
|---|---|---|
| TRK58-KPA65536R4096S3MK01 | 58 mm clamped flange design, 10 mm keyed solid shaft in the exact TWK installation drawing. | 65,536 positions per turn and 4,096 turns, Safety over EtherCAT, M12 connector configuration. |
| TRK58-KA65536R4096S3MK01 | KA clamped flange with 10 mm shaft and flat instead of the KPA parallel key. | Check the complete safety device identity, hardware revision and commissioning data. |
| TRK58-STA65536R4096S3MK01 | STA synchroniser flange with 6 mm shaft and flat. Match the pilot and coupling. | Compare the exact TRK/S3 configuration and safety record before replacement. |
Production and end-of-life status
TWK lists Safety over EtherCAT encoder families and provides TRK/S3 documentation. Confirm exact hardware version, orderability and safety support before purchasing.
Specifications
| Parameter | Value and scope |
|---|---|
| Resolution | 65,536 positions per turn and 4,096 turns in the reference order code. |
| Shaft and flange | 58 mm design with clamped flange, 10 mm shaft with parallel key, exact KPA installation drawing. |
| Supply | 9–36 V DC, nominal 24 V, per the TRK/S3 technical data. Apply any installation-specific supply conditions. |
| Network | EtherCAT with FSoE for the specified device. Match hardware and manual revision in the approved safety design. |
| Connections | Separate M12 supply and D-coded Ethernet paths. Use the exact connector drawing for port orientation. |
The values in this table apply to the reference build unless a row identifies another scope. Main technical PDF.
Mounting and fit
The 13348 sheet identifies the KPA keyed shaft and clamped flange. Compare the pilot, shaft engagement and coupling keyway before fitting. Check the machine's coupling and retention documentation and record the shaft datum. Inspect for key damage, movement or mounting play after isolating the machine.
Treat the mechanical position link as part of the approved safety application. Follow the machine's documented attachment method and safety validation after mechanical work.
Interface and measuring method
The encoder supplies position to the EtherCAT master and exchanges safety-related data using FSoE with a compatible safety controller. Ethernet link, EtherCAT state, process data and the validated safety connection are separate observations. The safety controller checks its configured connection and diagnostics. A working link alone cannot establish the machine's safety state.
Verified wiring
Use the 13348 installation drawing to identify the supply port and the D-coded Ethernet ports. The table gives functional pins from that drawing. Check the exact connector view, hardware revision and cable before handling the circuit.
| Connector | Documented functional contacts |
|---|---|
| Supply, A-coded | 1 +UB, 3 0 V. See exact drawing for remaining positions and shell. |
| EtherCAT, D-coded | 1 TX+, 2 RX+, 3 TX−, 4 RX−. |
Verify the cable shield and port assignment per the machine documentation. Preserve the safety controller configuration and connection mapping.
Cables inside the motor and at the machine
Use the approved EtherCAT M12 D-coded cable for the exact port and a separately verified supply cordset. A four-contact Ethernet cable and a supply connector serve different roles. Trace each cable end against the machine drawings and note the port order before removal.
Fault checks
External checks. Record the exact label, alarm, drive status and when the fault occurs. Look for visible plug damage, contamination, cable strain and looseness without opening a live assembly.
Isolation before internal work. Follow your site’s lockout procedure. Secure the load against movement, isolate all motor, drive and separate feedback supplies, allow the specified discharge time and verify absence of voltage. A qualified technician should perform internal and electrical checks. Unplug or reconnect only with the applicable circuits safely de-energized.
Harness continuity. Check resistance only on a harness you can disconnect from both the device and the receiver. Compare with shorted meter leads, flex gently at strain reliefs, and test for unintended shorts between conductors and to the shield. Use the schematic to recognize intended bonds. Keep resistance and insulation testers away from connected electronics.
| Observation | What to verify |
|---|---|
| No link at affected port | Check supply and the isolated network cable, connector and port mapping. Compare with the engineering topology. |
| EtherCAT link present, FSoE fault | Capture the safety controller's exact diagnostic and verify device identity, connection parameters and documented hardware revision. |
| Position shifts without communication loss | Inspect key and coupling after isolation, then validate position and direction according to the machine procedure. |
Powered checks. A qualified technician can fit an approved breakout while de-energized, secure motion, and compare documented supply and return at both ends under the specified load. Use the approved receiver or instrument to observe data or signal pairs. Return to an isolated state before changing connections.
Motor and drive applications
Use the guide for an approved FSoE installation with the exact TWK TRK58/S3 configuration. The safety controller project and machine risk controls determine the safe operation and required validation. Refer faults affecting safety functions to the qualified person responsible for that machine.
Angle of alignment and commissioning
Record existing position, configuration and machine datum. After installation, establish the OEM reference and validate the safety-related position and motion functions using the machine builder's procedure and qualified acceptance checks. An encoder reading or comparison on a bench is an electrical diagnostic only.
Drawings, pin maps and manuals
- Main technical PDF. Start with the exact type or variant marked in the guide.
- Manufacturer or exact product reference. Use the order code and select the applicable downloads.
- TWK TRK 13349 ME safety instructions. Use the hardware version and exact order-code coverage. Check the matching EtherCAT device file on the manufacturer page.
- TWK TRK 13348 KE keyed-shaft drawing. Locate the exact KPA drawing, electrical connections and safety references.