Identify the fitted part
| Guide scope | Yaskawa / Mazak Spindle ABZ feedback — Motor application |
|---|---|
| Feedback identity | Record the fitted feedback maker and complete designation; the named motor family is not a sensor part number. |
| Manufacturer MPN / full suffix | Spindle ABZ feedback is the scoped family/designation. Match every additional character on the fitted label before ordering. |
| OEM service ID / motor order | Not established for a specific fitted unit. Record the full motor label, feedback option and any OEM service ID separately. |
| Interface | Incremental ABZ |
| Documented starting connection | TI-5693, 17-contact MS |
| Material distinction | TCG426 is USAEE motor/Nemicon and TCG343 TFUE; neither establishes this spindle connector map. |
Specialist testing: connection before conclusion
| TI-5000JX bench scope | Check the documented position channels and separately identified index/commutation/tach paths. Exact output level, pin map and fixture must be verified. |
|---|---|
| Starting lead / fixture | TI-5693, 17-contact MS |
| Profile / module | Exact supply, output level, channel set and any amplifier to verify. |
| TI-3000JX motor-run scope | Bench feedback scope only. This spindle cable does not establish TI-3000JX motor-run support. |
The admission evidence is Mitchell Test Cable Index by Manufacturer Support — PDF page 8, Mazak, TI-5693 row. Verify installed tester software, the actual sensor option and the fixture before connection. A bench result describes the tested configuration; it does not by itself clear the complete drive, brake, machine cable or loaded axis.
Production and replacement status
Current production status, exact-order stock and an approved successor have not been confirmed in the cited evidence. Retain the installed label and ask for an exact-order check before selecting a replacement.
Specifications and interface
| Verified technical boundary | Identify the Mazak/Yaskawa spindle connection and separate feedback faults from drive-side issues. |
|---|---|
| Supply / output compatibility | Use the complete fitted label and its wiring drawing. No universal supply, receiver level or excitation is assigned to this family guide. |
| Exact dimensions, torque and pins | Use the scoped drawing or request it through the enquiry. Values from another suffix, connector view or motor revision are not substituted. |
A and B provide relative motion and direction when the receiver and decoding mode match the output. Z, N or reference is a separate datum channel where fitted. Pulse periods, x1/x2/x4 edge counts and machine travel scaling are different quantities. Where this application names UVW or Hall commutation, assess those signals independently; do not derive their phase from a healthy A/B count alone.
Mechanical fit and retention
Photograph the incoming shaft/coupling position, locating seat, restraint, fasteners and cable exit before removal. Check accessible looseness, contamination, bearing roughness and signs of rubbing after isolation. Identify whether the assembly has its own bearings, a hollow-shaft clamp or a motor-retained sensor; the exact drawing controls that decision. Do not lever against a sensing disc or apply a torque from a similar-looking model.
The Mazak/Yaskawa spindle ABZ row lists TI-5693 and 17-contact MS. Record both machine-builder and motor/feedback labels. Similar connector appearance does not make it the FANUC TI-5034 or Mitsubishi TI-5698 spindle connection.
Wiring and connector boundaries
Map five boundaries separately: the sensor plug or PCB, internal motor loom, motor bulkhead, external machine cable and drive/tester end. Record connector gender, keying, contact numbering and whether the drawing shows mating or termination side. The documented Mitchell lead is a starting fixture, not a pin map for a handmade adapter. Keep power, temperature, brake, shield and feedback contacts identified individually.
Starting connection for this guide: TI-5693, 17-contact MS. Use the source below for its named scope. Any unverified pin assignment remains open until the correct drawing is available.
Internal loom and machine cables
No internal OEM harness number or universal extension has been verified for this exact fitted order. Obtain the motor assembly drawing and photograph both loom ends before sourcing it. A fixed installation cable and a cable-carrier extension may have different flex and shielding requirements. Do not convert the Mitchell test-lead number into an OEM replacement part number.
Practical fault checks
Isolation and measurement conditions
Secure moving loads, isolate and lock out the relevant energy sources, follow the specified discharge time and have a qualified technician verify isolation before physical inspection or resistance checks. Disconnect both cable ends before continuity/short testing. Powered supply measurements, rotation, retention work and alignment require the approved fixture and procedure.
| Configuration-specific check | The Mazak/Yaskawa spindle ABZ row lists TI-5693 and 17-contact MS. Record both machine-builder and motor/feedback labels. Similar connector appearance does not make it the FANUC TI-5034 or Mitsubishi TI-5698 spindle connection. |
|---|---|
| Fault appears when the machine cable moves | With the system isolated and both ends disconnected, inspect flex points, connector engagement and repaired sections. Check end-to-end continuity and unintended shorts against the actual pin map, accounting for intentional shield bonds. |
| No feedback or intermittent loss at the drive | After label and fixture verification, have a qualified technician check the specified supply or excitation through an approved breakout. Compare at the source and load under the OEM procedure; never assume a voltage from the connector shell. |
| Wrong direction, count or reference position | Compare A/B ordering, the selected decoding factor and the fitted pulse rating. Verify reference and commutation paths independently; do not swap wires experimentally on an energized servo. |
Alignment, reference and memory
Preserve the spindle orientation datum, direction, index relationship and drive configuration. A spindle feedback index is not a synchronous servo commutation setting. Use the exact spindle-drive procedure for orientation or parameter changes; the cable-index row does not establish a TI-3000JX motor-run setup.
Motor and drive applications
Spindle ABZ feedback. TCG426 is USAEE motor/Nemicon and TCG343 TFUE; neither establishes this spindle connector map.
A matching maker, connector shell or protocol name is not a complete compatibility chain. Keep motor order → feedback option → internal loom → bulkhead → machine cable → drive configuration recorded separately. No unverified alternate part is offered by this guide.
Drawings, manuals and evidence
- Mitchell Test Cable Index by Manufacturer Support — PDF page 8, Mazak, TI-5693 row
- Generic Incremental Quadrature Pulse Encoders — Named article section, model or attached table. See each proposal row for the exact scope and locator.
Exact OEM technical PDF remains to obtain. The Mitchell reference establishes only the documented device or motor/feedback connection; it does not fill missing ratings or pins.
Common questions
What should accompany a Spindle ABZ feedback enquiry?
Send clear photographs of the motor and feedback labels, every suffix/ID, both connector faces, drive model, exact alarm and the circumstances of the fault. Include recent wiring, bearing, encoder or parameter work.
Can the listed Mitchell lead be used as a replacement machine cable?
The lead is documented for the stated test connection. OEM internal looms and machine extensions require their own part numbers, pin maps and mechanical ratings.
Does a successful feedback bench test prove that the motor can be run?
Bench feedback scope only. This spindle cable does not establish TI-3000JX motor-run support. A complete run assessment also checks motor power, brake, protection and mechanical conditions.
When does a site visit or send-in evaluation make sense?
A site visit can help when the fault depends on the drive, installation or moving cable. Send-in evaluation can isolate a removable feedback assembly or supported motor configuration. Agree scope, packing, availability and turnaround with SpareFaber after identification.
Request a scoped service evaluation
Use the existing encoder enquiry form with the labels, alarm and connection photographs. Specify whether you need UAE field diagnosis, installation/alignment assessment or send-in testing. Turnaround and repair scope are confirmed after review of the fitted configuration.